From the clips I've seen online and I think on the diamond, the holes in the back cover for the camera lens and (in the case of the touch pro) the light, have a clear plastic lens within the back cover which some reviewers criticised because it could get smeared with fingerprints etc.
Taking the back off mine this morning to put battery and sim in, noticed that there is no clear plastic cover, the square 'frame' is there in the back of the back cover to mount such a piece but it has not been fitted (assuming mine hasn't fallen out).
Same with everyone else?
kempas said:
From the clips I've seen online and I think on the diamond, the holes in the back cover for the camera lens and (in the case of the touch pro) the light, have a clear plastic lens within the back cover which some reviewers criticised because it could get smeared with fingerprints etc.
Taking the back off mine this morning to put battery and sim in, noticed that there is no clear plastic cover, the square 'frame' is there in the back of the back cover to mount such a piece but it has not been fitted (assuming mine hasn't fallen out).
Same with everyone else?
Click to expand...
Click to collapse
Yep, same here, you're all good.
Cheers, must have been a last minute thing then in response to criticisms.
kempas said:
Cheers, must have been a last minute thing then in response to criticisms.
Click to expand...
Click to collapse
Well ours are inset, so I wouldn't worry about fingerprints, but what does worry me is that now it's easier for dirt to get trapped in there.. At least it's easy to clean it out without the plastic cover, imagine trying to get a Q-tip down in there?
Easier to just slide the back of to clean the lens if need be.
kempas said:
Easier to just slide the back of to clean the lens if need be.
Click to expand...
Click to collapse
Exactly, but if they put a plastic cover on the back like the Diamond, you couldn't get dirt out from inside the case. Major PITA.
I recently bough the extended battery pack (HTC BP E270) and I am satisfied with the new look and feel of the phone, not to mention the improved up time. One very disappointing thing however, is that the new back cover comes off very easily. Simply pulling the phone out of my pocket makes the cover fall off.
The cover is not broken in any way.
Is there a way to make the cover fit tighter so that it doesn't accidentally fall off.
Put glue under it or something I got the same problem as you, backcover to my 1800 mAh is very plastic and the bottom is not fully pressed onto the phone or what should I say.
Thanks Artie. I would however, like to be able to change the cover for the slimmer one at certain occasions. How do you remove the cover if you glued it onto the phone?
Gripenstedt said:
Thanks Artie. I would however, like to be able to change the cover for the slimmer one at certain occasions. How do you remove the cover if you glued it onto the phone?
Click to expand...
Click to collapse
I use double sided tape.
actually, some ordinary transparent tape might be enough to do the trick.
i don't have an extended battery myself so i don't know why exactly it doesn't fit properly, but maybe you can tighten the hold a little at some places by putting some tape on your phone near where the cover holds onto your phone.
Back Cover
blue tac my friends just a small bit in hte right place
Back Cover
blue tac my friends just a small bit in the right place
I have the same original HTC extended battery, It fits right but comes off very easy.
What is blue tac? And where to apply it?
i have the same problem...i think that double sided tape is the best way to resolve this problem...i'll try
p.brazauskas said:
What is blue tac? And where to apply it?
Click to expand...
Click to collapse
http://cgi.ebay.co.uk/Bostic-Blue-T...y_CA?hash=item3ca579e18f&_trksid=p3286.c0.m14
...or bubble-gum, if you're stingy
(i already broke one of the corner bits because of the constant slip-off)
There are two screws on the bottom of the Tf by the charging port. Then on the back there are clips all around the outer edge of the "Asus" panel. Use any non marring tool for the clips. Once all the clips are loose, the bezel around the screen comes off frome the front. It seems to bemostly plastic with a metal overlay. Then there are ten or eleven philips screws that hold the rear panel on.
Sorry no pics
So the metal bezel comes off first then followed by the plastic back panel which is held in by screws?
Sent from my Transformer TF101 using Tapatalk
Thats correct. You can see the screws for the back after the bezel is removed.
The metal around the edge is seprate from the back plastic and the front glass. However the metal is extreemly thin and WILL bend with any kind of proping. Also once u remove it getting dust under the glass is going to happen. Also the plastic clips are very ****ty and if one bends or brakes the transformer will not click back on. Its not worth opening this thing up. If u have a issue with your unit call asus and have them fix or return to store.
cowballz69 said:
The metal around the edge is seprate from the back plastic and the front glass. However the metal is extreemly thin and WILL bend with any kind of proping. Also once u remove it getting dust under the glass is going to happen. Also the plastic clips are very ****ty and if one bends or brakes the transformer will not click back on. Its not worth opening this thing up. If u have a issue with your unit call asus and have them fix or return to store.
Click to expand...
Click to collapse
Thanks to everyone who posted this information!
The only thing that bothers me about the TF is the creaking, so I was thinking about fabricating some pieces to upgrade or replace the back, bezel, or both.
couple of questions for you...
--Were you able to determine exactly where the creaking comes from? Is it just the flimsiness of the back panel or the way it all mounts together?
--Also, you mentioned dust getting under the screen after reassembling- so the glass is a completely separate component? How does it attach to the rest of the unit?
--Finally, are there any warranty/tamper seals that get broken during dissassembly?
Thanks again!
I didn't go any further than removing the bezel out of fear that I would break something or not be able to get it back together. I didn't get any dust under my screen and there wasn't a single tamper seal that i saw
I just started developing this odd creaking noise near the bottom and sides of my S4G. Even with a Seidio Active case wrapped around it, the creaking can be felt and heard when hitting the bottom buttons.
The fix is pretty easy. You just need to decrease the amount of movement the back cover has.
I had some .010 mil fiber (fish) paper laying around so I cut a small square that covers the sim card and microsd card area. You can probably use something else, but hey, why not use some insulated paper if you have it.
Lay the paper on top of the area and then slowly place the back cover back on. No holes are in that area above the sim and microsd, so no worries there. You should see an immediate improvement
I needed more than that to stop the creaking/screen movement.
Pathetic we have to go to these lengths
jlevy73 said:
I needed more than that to stop the creaking/screen movement.
Pathetic we have to go to these lengths
Click to expand...
Click to collapse
What did you have to do?
I tried used two squares of paper, but that made the back bulge out a little too much to my liking.
GideonX said:
What did you have to do?
I tried used two squares of paper, but that made the back bulge out a little too much to my liking.
Click to expand...
Click to collapse
I took a post-it and folded it twice. Then placed it on the bottom right area and closed up the cover. For me when I press down on the bottom right side of the screen the whole screen sort of depresses a bit. Only way I could get rid of that was to place the paper in that region. Problem solved.
Post it would have been my backup method
Sent from my HTC Sensation 4G
buy another battery, i recently got an anker also had the creaking problems, noticed the anker is a TINY bit thicker than the stock battery and it removed that problem completely. and that anker battery was DIRT cheap
I just lined the case with some scotch tape. from the bottom to about 3/4 of the way up. I just went around the antenna nubs and the usb hole.
Posted this in another thread, but felt it was valuable here too...
Got the creaking here also, definitely a design flaw. Being obsessive with my devices i couldnt live with it!
I do not recommend putting paper in the cover to fill the gap, as this is just expanding the cover further making it even MORE loose when the paper is not in there. Also i wouldn't recommend it because the paper pushes the back cover out a little more, you may loose a connection for the ground. Which is the little metal springy thing, half way up the right hand side. Obviously its not a good idea to 'push' the cover further away from this ground spot. I have heard that people have had issues with screen responsiveness due to a static build up from not grounding properly.
What i did to fix this problem was a bit of a kitbash of sorts.
Mine was creaking on the bottom right area, like most. The problem is there is too much play between the little black catches on the battery cover and the latch on the handset. Instead of filling up the gap between the phone and the cover (Ala paper, card in the cover) I closed it!
What you need to do is get some very thin plastic film. Like that on kids toy packaging etc. Not the thicker stuff though. This stuff would be under 1mm thick. It came as a viewing window in the box my new wallet came in. So you can sorta imagine what im talking about.
I cut a piece about 10mm long and as wide as one of the two little black catches. I applied a VERY thin coat of super glue to one end of the film. Just enough to cover the area under the catch. Then i carefully placed the film with the superglue on it under the catch, and then quickly applied some pressure to it with some tweezers. Then i carefully cut the excess off with a pair of finely tipped nail scissors.
The result is that it now PULLS the screen/phone INTO the cover more by making the little black catch thicker. Not the opposite (paper method), which pushes the cover out, creating a further problem of adding more paper under the cover over time as the cover expands/loosens to compensate. Not to mention a possible grounding loss and resulting damage.
Hope this helps some people that have had multiple replacements or could not be bothered replacing for such a cosmetic issue. (Like me). It definitely works, just got to get your surgeon on and be accurate with your placement of the film.
Apply this to what ever side creaks the most, and bam its gone. Nice. Solid phone... again.
If anyone wants more specific details etc, im all ears.
Regards,
Matt.
will try it with an double side film ...
i mean a film that hold back cover and phone together ;-) i think doing paper in there will do damage with time
I contacted HTC and they sent me another/new one. No more creaking!
RaptorRVL said:
I contacted HTC and they sent me another/new one. No more creaking!
Click to expand...
Click to collapse
Back cover or whole phone?
I have the same problem too. And it just seems to get more and more "cracking"
Hi all,
Here's my 5 minute wireless charging mod. Now new and improved so that NFC performance is not affected at all. I've also posted step-by-step pictures to aid in explaining the hack.
You need to make one decisions before you start, do you care more about using NFC or using a magnetic compass app? The reason for this is that the magnetic sensors are in the bottom part of the phone. If you use magnets instead of metal disks, this will affect the accuracy of the magnetic sensors, so a compass app will not work well. But if you use the metal disks that come with the Palm case, and you do the hack with the coil very low in the phone case, it won't hold through a case, so you may need to build some sort of rest for it. I use NFC all the time, and never use the compass, so decided to go with replacing the metal disks with N42 magnets. Also, this charging mod works fine through most cases, I've tested it with TPU and with the Rock cases. It might not work through an Otterbox, I haven't tested it. Using magnets makes it more likely to work with cases. Alternatively, you could use the nonmagnetic disks, but rig up some sort of support so that the phone would sit in the right place on the charger without depending on magnets.
No soldering, no carving, the only tools you need are a knife, and some scotch tape! Some sort of plastic tool, even a plastic knife is helpful too.
The shopping list is below, and totals about $17-$19 depending on which vendors you buy from. The links below are from Amazon, for simple one-stop shopping. You may want to buy two Touchstones for home and office. I wouldn't try to cheap out and use another AC adapter, as most of the adapters I tried failed to work with the Touchstone base.
Palm Pixi Charging back
Palm Touchstone charger
Palm Touchstone AC adapter (important, most chargers won't work)
Copper Tape
OR
Copper tape from Michael's
50% off coupon for Michaels
If you want to replace the metal disks with magnets, to make the phone hold better to the charger, then buy these magnets from Amazon, or
http://www.amazon.com/Applied-Magnets-Earth-Neodymium-Discs/dp/B0012AUU84/ref=sr_1_1?s=hi&ie=UTF8&qid=1350067151&sr=1-1&keywords=neodymium+disk+magnets+1%2F4+1%2F32
these from ebay: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=190734931794
Total = $17-$19
Time: 5 minutes.
Okay, here's what you do.
Picture 1: Shows the Palm Pixi charging case as you will recieve it. (I recommend the Palm Pixi, not the Palm Pre, as the polarities are reversed on the Palm Pre.) After you get all the parts, gently peel the black tape off the Palm pixi case, (Picture 2 and 3). Then gently and carefully remove the circuit board (Picture 4), the silver metallic tape (Picture 5), the coil (Picture 6), and metal discs. Preserve the silver foil tape, you will need it. You may also want to preserve the black tape.
Next, I show that you can make a template for positioning the coil and discs/magnets by cutting up the Palm Case (Picture 7), and then drilling out holes where the metal discs and the center of the copper coil are (Pictures 8 and 9). I then made a paper template, which is easier to use (Picture 10).
Now here's the clever part of the hack. Put the coil into your Samsung battery cover upside down, as shown in Picture 11. Then fold the L shaped flexible circuit board up as shown in Pictures 12 and 13. This positions it so that you can make an easy connection to the phone using just copper tape. You will run small pieces of copper tape from the top and the bottom power terminals, which are those little square metal terminals shown in Picture 13. (Picture 14 and 14-5). You can then position the discs or magnets. The easiest way to do this is to plug in your Touchstone base, and then lay the back cover on the Touchstone charger. Put your magnets or discs in, and make sure they align with the magnets in the Touchstone base. Note that if you use magnets, you may have to flip them to get them into the right orientation. Use the template you made to check the alignment. Once you get it like the picture, just tape everything down with scotch tape. (Not the terminals.) (Picture 14-5 shows this clearly.) Note that you need to put back in the silver tape over the coil as shown in Picture 14-5, otherwise it won't charge.
Cut the copper tape down to about 1/8 of an inch, and tape two extensions from the charging terminals in the phone. I used a pencil to poke the tape down into the little wells so there was a good contact. Next, lay down the cover and the phone, and tape copper tape to the charging terminals on the charging coil so they will hit the tape on the phone when you close the cover. I folded under the final 1/8 of an inch to make a little lump, to make it more reliable. (Picture 16).
It's useful to check your work with a voltmeter. Place the battery cover with the mod onto the Touchstone base, and check to make sure you are getting 5.5 volts off of the two terminals. Then after you add the copper tape extensions, make sure they are reading the same voltage. If you are not getting voltage, press the tape harder onto the terminals, as the sticky side is less conductive. You could also fold over the copper tape onto the terminals, and scotch tape it down.
Finally put the back onto the phone, and test to see if you get the popup message in Picture 19. If all is good, then you can open it up again and add back the black tape to make it pretty (if you care). (Picture 15). Then should be no real bulge as shown in Pictures 17 and 18.
If it's not working, there are three possible reasons. One, you have a bad connection between the terminals and the copper tape. Check it with a voltmeter. Two, the copper tape that goes into the phone's charging terminals is not making good contact. Fold over a bit of the tape, and gently jam it down into the terminals. (Gently so that you don't break them off!) The third reason is that the tape pieces from the coil are not making contact with the pieces on the phone, see Picture 16 for how the alignment should be. If you are getting the popup repeatedly, then you have an intermittent connection.
Oh, one more thing. Be sure to test this with your phone at less than 100% charge, as it won't work if your phone is 100% charged! I found this out the hard way!
Close the cover and you are done! It sounds complicated, but actually if you just copy the picture, it takes 5-10 minutes.
Here are the pictures, numbered as in the instructions:
https://www.dropbox.com/sh/qpymo0x6rpmkezx/XMT4z_wDq_/New%20Improved%20wireless%20Charging%20Hack
Thank you's appreciated.
A FEW UPDATES: Here are a few updates from clever ideas from our members.
You can use hotglue to attach everything once you are sure of the location.
The disks in the Pixi cover are metal, not magnets. Replace them with magnets for a better hold.
The magnets (and the coil) could go in a case like an otterbox, instead of inside the phone. Then you'd run thin wires into the battery case. Or you can run the copper foil out from inside your phone so that it connects with the mod inside the case. See post #217 for a way to do this elegantly.
BE aware, the Palm Pre polarities are reversed, so if you use a Palm Pre back, you will have to reverse the polarity.
IF YOU AREN'T GETTING VOLTAGE:
The most common problems are:
1. You are not using a palm charger and cable for the Touchstone. Most chargers/cables won't work, it's better to just use the Palm charger, they cost $4 on Amazon. Are you using the Palm charger/cable?
2. Your copper tape is not making good contact with the little prongs on the flexible circuit board. Try removing the tape and checking voltage on the prongs themselves. Then put the copper tape on firmly, and check the tape for voltage.
3. The coil is not in the right place. You may want to make a template like I suggested to get everything aligned properly. You won't get voltage if the coil is not just right. Use scotch tape to get everything working, then you can use more permanent methods.
4. You used a Palm Pre back instead of a Palm Pixi back, and you forgot that the polarities are reversed on the Pre back.
5. You are not getting a good contact at the charging pins on the phone. Do this: (thanks nonsns3)
Cut tape a quarter inch wide. Ball up a quarter inch on one end and tape it so that the ball is right above the connector pins. Also make sure the exposed part of the ball is not the sticky side. Using a pen, push the ball end into the hole so that it contacts with the pin and you should be all set. This should be the easy part.
Most of the time the two issue areas are:
1) copper tape doesn't make good contact with the pin on the back cover because one side is adhesive.
2) copper tape doesn't make contact between the back cover and the copper tape on the phone itself when you close the cover.
FAQ:
Can I charge the regular way with a micro usb charger after I make this mod?
Yes, it works fine. Just don't plug in the micro usb and the touchstone simultaneously, as I don't know what would happen.
Should I use magnets in the mod instead of the metal disks?
It depends on how thick a case you plan on using, and how firm a grip you want the phone to have on the Touchstone base. You can always use scotch tape and test it both ways.
Will this interfere with NFC?
No, typically it won't, and you can decide on the placement of the mod over the battery, or below the battery. Below the battery has no effect on the NFC, over the battery makes NFC a little more finicky about positioning.
Will this interfere with my compass app?
Only if you use magnets instead of the stock metal disks. And then only if you put the mod low in the battery cover, as the sensors are low down.
Will this interfere with GPS?
Absolutely not.
My phone slides off the Touchstone base, what should I do?
I've modded my bases so that the top is horizontal instead of sloped, which makes phone alignment easier. I used Sugru, but any substance that allowed you to fit in the bottom will work.
Everything was working great, now it stopped working.
Usually the reason is that you've dislodged some connection inside the phone. If this happens, just open up the battery cover, and check all the connections, especially where the copper tape meets the charging terminals inside the phone.
Should I put magnets onto the Touchstone base?
Yes, see my attached picture, this helps with a firmer grip, and may even obviate the need for using magnets inside your SG3 case. Note the magnets can attach two ways depending on their polarity.
I find the charging noise annoying, especially after the phone is fully charged, and it keeps beeping at me.
Yes, on some ROMs this is very annoying. To fix it if you have root, use Root Explorer to got to /system/media/audio/ui . Then press the button on the top right that says, "Mount R/W" so you can change the files. Find Charger_Connection.ogg and either delete it or if you might want it back, just rename it to Charger_Connection.ogg.bak . Reboot, and no more noise, but be sure you see the charging indicator on the phone since you won't hear a beep.
I am considering doing this but with a twist. I would put the coil between the otterbox rubber and hard plastic and put the wires though a hole in the battery door. I would probably have to cut or thin out the rubber so it would fit flush, but I am confident it could go through the fairly thin otterbox plastic.
Sent from my SCH-I535 using Tapatalk 2
This seems like a cool idea but whats the point if it needs to stay on the touchstone? (If im correct on that)
Nice work. I really like this and will be doing it as soon as I get money for the parts. Thanks for sharing
Sent from my s3 using xda premium
I'm pretty sure all wireless charges have to sit on their charging bases. The simply alleviate the need to hook up cables to you phone (which could as to the life of the phone considering how many times you'll be plugging it on over the next year or two).
--
Sent on the fly.
Just curious. Does this mod interfere with NFC?
Sent from my SCH-I535 using xda premium
The point here is to eliminate the foolish cases that wireless chargers have to equip your phone with to work. This is one of those amazing things that this site has to offer. Fine work my friend!
Sent from my SCH-I535 using xda premium
android94301 said:
Hi all,
Here's my 5 minute wireless charging mod.
No soldering, no carving, the only tools you need are a knife, and some scotch tape!
The shopping list is below, and totals about $17-$19 depending on which vendors you buy from. The links below are from Amazon, for simple one-stop shopping.
Palm Pixi Charging back
Palm Touchstone charger
Palm Touchstone AC adapter (important, most chargers won't work)
Copper Tape
OR
Copper tape from Michael's
Total = $17-$19
Time: 5 minutes.
Okay, here's what you do. After you get all the parts, gently peel the black tape off the Palm pixi case, and remove the coil, and magnets. Preserve the silver foil tape, you need it. Mark the top of the magnets with a marker, and gently dig them out with a knife. Don't break them.
Pop open your Samsung Galaxy S3.Lay the back cover on the Touchstone charger, and put the magnets in the same orientation they were in in the Pixi cover. If you flip the orientation, they will be too close together. Then lay in the coil, with the tape extending up to the right. Make sure there is enough room to add the copper tape later. You may need to slide the cover so the magnets are slightly to the left.
Once you get it like the picture, just tape everything down with scotch tape. (Not the terminals.) Cut the copper tape down to about 1/8 of an inch, and tape two extensions from the charging terminals in the phone. I used a pencil to poke the tape down into the little wells so there was a good contact. Next, lay down the cover and the phone, and tape copper tape to the charging terminals on the charging coil so they will hit the tape on the phone when you close the cover. I folded under the final 1/8 of an inch to make a little lump, to make it more reliable.
Close the cover and you are done! It sounds complicated, but actually if you just copy the picture, it takes 5 minutes.
Several tips:
I actually replaced the magnets with some that were a little more powerful, but you can get away with using the original magnets.
If you want to have a more finished look, you can use the black tape cover from Pixi cover to cover over the mod, but I'd tape it first, and make sure everything works.
Here are the pics:
Thank you's appreciated.
Click to expand...
Click to collapse
Wouldn't those magnets mess with the phone's magnetometer thus things like the compass? I wouldn't see a problem to do away with the magnets and just put it on a regular wireless charging pad so there isn't a need for the magnets. Other than that issue, kudos for the directions for such a cheap mod :good:
RyanW114 said:
Wouldn't those magnets mess with the phone's magnetometer thus things like the compass? I wouldn't see a problem to do away with the magnets and just put it on a regular wireless charging pad so there isn't a need for the magnets. Other than that issue, kudos for the directions for such a cheap mod :good:
Click to expand...
Click to collapse
Hi,
I just tested it with Smart Compass, and it seems to work. How many people use a compass app anyway? Don't most use GPS, which isn't affected by the small magnets.
In terms of NFC, I haven't tried NFC, so I don't know. But other's who've used the same system don't have problems with NFC. You could always mount the coil lower, so it wasn't near the NFC chip.
I don't understand the question about the phone needing to stay on the Touchstone. How is that different from the phone needing to be plugged in while charging? The major advantage of this mod is that a) it's way cheap and way cool, and b) you won't wear out the micro usb port plugging in and out. Also, I find it much more convenient to just lay my phone down on the charger whenever I am not using it, so it's always fully charged.
con247 said:
I am considering doing this but with a twist. I would put the coil between the otterbox rubber and hard plastic and put the wires though a hole in the battery door. I would probably have to cut or thin out the rubber so it would fit flush, but I am confident it could go through the fairly thin otterbox plastic.
Sent from my SCH-I535 using Tapatalk 2
Click to expand...
Click to collapse
That would work, although with slightly stronger magnets like what I used, my phone has a Rock Case on it, and everything works right thru the back cover and the Rock Case.
Ahh I see, not worth it to me, I use my phone while charging a lot.
Sent from my SCH-I535 using xda premium
android94301 said:
That would work, although with slightly stronger magnets like what I used, my phone has a Rock Case on it, and everything works right thru the back cover and the Rock Case.
Click to expand...
Click to collapse
Glad to hear this works through the Rock case!
I already had all the parts you listed in the mail before you started this thread, and my biggest two worries were:
1. Slight bulge from coil might prevent Rock case from fitting
2. Rock case will prevent this from charging
Great to know neither of these will be a problem!
K
android94301 said:
Hi,
I just tested it with Smart Compass, and it seems to work. How many people use a compass app anyway? Don't most use GPS, which isn't affected by the small magnets.
In terms of NFC, I haven't tried NFC, so I don't know. But other's who've used the same system don't have problems with NFC. You could always mount the coil lower, so it wasn't near the NFC chip.
I don't understand the question about the phone needing to stay on the Touchstone. How is that different from the phone needing to be plugged in while charging? The major advantage of this mod is that a) it's way cheap and way cool, and b) you won't wear out the micro usb port plugging in and out. Also, I find it much more convenient to just lay my phone down on the charger whenever I am not using it, so it's always fully charged.
Click to expand...
Click to collapse
Last time i checked the 'magnets' in the palm pixi cover are not magnets but small pieces of metal. The magnets are in the pixi charging pad. I did this mod a long time ago and just used some really really small wires to complete the connection, i have been meaning to buy the copper tape but, lazy.
Nice mod!! If you could post a vid of a tutorial that would be sweet!??? I have always been the type to learn the best by watching it in action... Great job though!!:good:
TheMorlince said:
Last time i checked the 'magnets' in the palm pixi cover are not magnets but small pieces of metal. The magnets are in the pixi charging pad. I did this mod a long time ago and just used some really really small wires to complete the connection, i have been meaning to buy the copper tape but, lazy.
Click to expand...
Click to collapse
No, they are small and thin neodymium magnets. What phone did you do it on "a long time ago"?
Ordered
Just ordered the parts. Touchstones for $3.50 and back covers for $3. Makes me sad though to see how Palm has fallen. My wife had a Pre Plus and touchstone and we both loved that phone. Probably would have bought a Pre 3 if they had ever come to market. Got 2 touchstones so I can have one at work. I will most likely epoxy the components to the battery cover since new battery covers are like $5. Should hold up better than Scotch tape over time.
Will report back when I get it all working.
nsmal24 said:
Just ordered the parts. Touchstones for $3.50 and back covers for $3. Makes me sad though to see how Palm has fallen. My wife had a Pre Plus and touchstone and we both loved that phone. Probably would have bought a Pre 3 if they had ever come to market. Got 2 touchstones so I can have one at work. I will most likely epoxy the components to the battery cover since new battery covers are like $5. Should hold up better than Scotch tape over time.
Will report back when I get it all working.
Click to expand...
Click to collapse
That's a good idea, maybe I will have two covers, one with wireless charging for most of the time, and maybe one plain one for travel, etc.You might want to play around with it a little first, using scotch tape, check out NFC, etc, before you commit to gluing it all down.
Can you post a video that would be really cool
Sent from my SCH-I535 using Tapatalk
F***ing brilliant
For those looking to glue & not use tape just use silicon as it is easy to remove with no damage if needed but more stout than tape
This is awesome, thanks! The cover fits after gluing all that extra stuff without a problem, right? And how fast is the wireless charging?