I have P9 Lite and Screen goes into sleep mode after 15 seconds. When I try to change it in Setting by clicking on say 10 minutes it wont change from the 15 seconds mode even with the 10 minute highlighted
michaelreeves1 said:
I have P9 Lite and Screen goes into sleep mode after 15 seconds. When I try to change it in Setting by clicking on say 10 minutes it wont change from the 15 seconds mode even with the 10 minute highlighted
Click to expand...
Click to collapse
Reboot into Recovery and perform "Wipe cache partition" . Reboot system.
Related
so when i am on battery, i have the options to turn off the backlight after 10 seconds. but the darn thing wont turn off after 10 seconds.
it ends up turning off after a 1 minutes or, but yet i have 10seconds specifically chosen.
and sometimes my brightness goes way back up and the selection to 2minutes.
why can't it registered what i want? 10seconds is all i ask for lol
My Fuze started going to sleep while connected to power even though it is set not to!
I have checked the settings under
Settings>System>Power>Advanced.
Set to:
On Battery Power:
X - Turn off backlight if device is not used for 30 sec
X - Turn off device if not used for 1 min
On External Power:
- Turn off backlight if device is not used for ...
- Turn off device if not used for ...
That is, Both boxes under external power are not checked, yet the device turns off the screen anyway after about 30 seconds either on or off power!! A press of any key while on power will bring it back on. On battery a touch of any key within 30 seconds will bring it back on, then after 30 seconds, I will have to press the power button to turn it back on.
I decided that it must be a software error, so I reloaded, AT&T Stock ROM, Skip Bloat, and it is still acting the same way.
Any suggestions???
Open the following registry key:
\HKLM\System\CurrentControlSet\Control\Power\Batt
Look for the value of PowerOff. If it´s not 0, set it to 0 an see if this helps.
H.
I have a key "BattPowerOff" I assume this is the one you are talking about, as there is no folder for "Batt".
It was set at 180. I have changed it to 0. I will see how it goes and report back.
Thanks!
After reg change above and soft reset, same behavior. Phone display switches off after 30 sec. While on bat, if I click any key within 30 sec of display switching off, it comes back on, after 30 secs, must push power key.
While on power, display switches off after 30 sec, and will come back with press of any key at any time.
Any more ideas?
bump - anyone???
Hello, I bought the Nexus 5 a month after it came out and recently the power button is going crazy (not physically): when i turn the screen on it sometimes presses the power button again and turning it off or presses the power button (long press) and shows me the power menu (Power down etc...) or presses it longer and restarts.
I tried to wipe date and cache via recovery mode (it took about 50 minutes to wipe the date. its a very long time but i read that it takes 30-60 minutes) and the problem is not solved.
What should i do??
Thanks in advanced.
Reflash factory images,
If it doesn't fix it, RMA.
harelmk said:
Hello, I bought the Nexus 5 a month after it came out and recently the power button is going crazy (not physically): when i turn the screen on it sometimes presses the power button again and turning it off or presses the power button (long press) and shows me the power menu (Power down etc...) or presses it longer and restarts.
I tried to wipe date and cache via recovery mode (it took about 50 minutes to wipe the date. its a very long time but i read that it takes 30-60 minutes) and the problem is not solved.
What should i do??
Thanks in advanced.
Click to expand...
Click to collapse
Something like this?
https://www.youtube.com/watch?v=p5U7Z9Cv7dQ
Hey guys,
My uk mate 9 was low on battery last night, it shut down and now it won't come back on. It's permanently stuck on the booting logo and occasionally the led blinks red and I get a red charging circle on the screen? Its been on charge all night and it's the same any ideas?
I would try recovering it with FunkyHuawei.
Sent from my MHA-L29 using XDA Labs
Try to boot into recovery,press volume up +power button and when u see the logo remove power button while keep pressing volume up till you get into recovery, wipe cache and reboot.
If it doesn't boot make factory reset from recovery again.
Are you using the stock charger and cable?
Since the upgrade to Android 8 Oreo I have a similar problem.
After two days uptime (i.e. time after a reboot), the screen won't turn on when clicking on the power button or the fingerprint scanner. Only holding the on button a few seconds it shows the power / reboot prompt. Clicking the screen or fingerprint scanner then turns it on.
After a reboot the problem does not appear for one or two days and then it starts over again. Even the alarm clock cannot be stopped.
I wiped cache and system cache but to no avail.
mermaidkiller said:
Since the upgrade to Android 8 Oreo I have a similar problem.
After two days uptime (i.e. time after a reboot), the screen won't turn on when clicking on the power button or the fingerprint scanner. Only holding the on button a few seconds it shows the power / reboot prompt. Clicking the screen or fingerprint scanner then turns it on.
After a reboot the problem does not appear for one or two days and then it starts over again. Even the alarm clock cannot be stopped.
I wiped cache and system cache but to no avail.
Click to expand...
Click to collapse
Exactly Same Here, anybody got an idea ?
biggir said:
Exactly Same Here, anybody got an idea ?
Click to expand...
Click to collapse
When it happened again, I connected my phone to my computer and started 'adb shell' and then 'top' which shows all processes running in order of CPU usage, like the same 'top' on Linux or macOS.
I saw that 'system_server' is on top with 100-110% CPU (multicore CPU hence above 100%). Is that correct ?
Hi,
does anyone have a way to leave the power saving mode after installing titzen 3.0?
I can not turn it off via the app or the watch ?
handsolo said:
Hi,
does anyone have a way to leave the power saving mode after installing titzen 3.0?
I can not turn it off via the app or the watch ?
Click to expand...
Click to collapse
only factory reset works :/
Ensure your watch is powered off.
Press and hold the Power/Home button (located on the right-edge) until 'Rebooting' appears at the bottom of the screen then release.
Power/Home button
Press the Power/Home button repeatedly until the 'Select REBOOT MODE' screen appers.
Select REBOOT MODE screen
Select Recovery.
Note Press the Power button to cycle through options
When 'Recovery' is highlighted as seen in the image above, press and hold the Power/Home button until the device reboots again.
Note Allow several minutes for the reboot process to complete.
Note To set up the watch after the reset has completed, refer to Initial Activation and Setup.
handsolo said:
only factory reset works :/
Ensure your watch is powered off.
Press and hold the Power/Home button (located on the right-edge) until 'Rebooting' appears at the bottom of the screen then release.
Power/Home button
Press the Power/Home button repeatedly until the 'Select REBOOT MODE' screen appers.
Select REBOOT MODE screen
Select Recovery.
Note Press the Power button to cycle through options
When 'Recovery' is highlighted as seen in the image above, press and hold the Power/Home button until the device reboots again.
Note Allow several minutes for the reboot process to complete.
Note To set up the watch after the reset has completed, refer to Initial Activation and Setup.
Click to expand...
Click to collapse
yup same problem here. first time using power save mode since running on version 3.0. sucks that this is a bug as i use this all the time when i want a notifications on the watch but low on battery. so far this update been pretty glitchy