Related
I got my TechSkin in the mail today, and just installed it.
My first impressions:
Design/Fit:
---------------------------
This Skinomi was designed for the Nexus 4, and it fits *perfectly*. The cutouts for the proximity sensor, front camera and earpiece are 100% accurate. The only thing that I would note is that the screen protector is about 0.3mm short on both the left side and the bottom, but that's too insignificant to have any affect on usability. Other than that, there aren't any major problems with the design.
Feel:
----------------------------
This thing sure is plasticy. It's nowhere near as smooth as glass, but that's to be expected of screen protectors. However, this screen protector is quite grippy when dry. This might prove to be a problem for gamers. I'll try playing Modern Combat 4 later, and I'll update the review accordingly depending on how my fingers feel. The Skinomi is definitely smooth enough for normal use, but it still can't compare with the super-smooth Gorilla Glass that it's designed to protect.
Look:
----------------------------
No Orange Peel! This protector is great. This has barely any orange peel effect at all, unlike the Zagg InvisibleShield protectors which I have for my Galaxy Nexus and my iPad.The screen protector is smooth and conforms to the curved edges of the screen very well. A word of warning for potential buyers: Getting the screen protector to stick properly onto the curved glass requires you to press and hold it down to the curve for at least 2 minutes, until the solution dries and it sticks. But once it's stuck, it's stuck for good.
If you have any questions, please ask! If you want more pictures I'll be more than happy to post them.
Link to Pics:http://imgur.com/5uz0X,j4lo2,WKtWV,MAEnD,G5XrH,q5Mkg
Update: Back Protector
Design/Fit
---------------
Again, the fit is spot-on. All the cutouts match with the correct spots on the device, and the cutout for the camera is just the right size.
No complaints here.
Feel:
------------------
Same grippyness as the front. I think that this is actually a good thing for the back: The Nexus 4 is a very slippery phone, and having a grippier plastic back should make it harder for the phone to slide off a table or out of my hand.
Installation:
------------------------
WORD OF WARNING: Be careful when installing the back. It's too easy for water from the installation to seep into the speaker hole, and who knows what kind of damage that can cause. I had some water go into the speaker (Not a lot, less than a drop), but still, better safe than sorry.
Update: Pics.
Link to images of the back: http://imgur.com/zUIoC,VLqHA,ScypJ,xfabx
UPDATE: Now that I've started to use the phone with the screen protector, the grippyness of the front screen protector doesn't seem to affect normal usage of the phone. In fact, it feels quite smooth compared to Zagg screen protectors, and I am quite satisfied with the Skinomi overall.
If you are looking for a screen protector for your Nexus 4, I'd recommend the Skinomi TechSkin.
I have had this for a week now. It really takes a few days to completely smooth out and it gets clearer. I don't notice any yellow tint at all. I'm liking it more and more everyday.
I have the carbon fibre tech skin waiting to be installed, normally I hate screen protectors and I'm concerned I will get a load of dust under it, did you guys manage to install it clean? No bubbles?
Sent from my cm_tenderloin using Tapatalk 2
Nathanation said:
I have the carbon fibre tech skin waiting to be installed, normally I hate screen protectors and I'm concerned I will get a load of dust under it, did you guys manage to install it clean? No bubbles?
Sent from my cm_tenderloin using Tapatalk 2
Click to expand...
Click to collapse
Did mine in the bathroom with the shower ruining on full hot. The moisture takes the dust out of the air.
Works every time for me. Good luck
I kind of like the grippy feel of it.
The phone felt really slippery before and i've had it slide off tables that were slightly angled but with this on it completely stays in place.
Carbon parts installed fine, I like the back plate but not overly keen with the side pieces, the screen protector.... I need another one I think, it is straight but has loads of streaks in it, going to leave it for a few days as skinomi suggest and see if it clears up...
Sent from my cm_tenderloin using Tapatalk 2
To add onto the OP's post, I did not have to press down on the front curved glass for the screen protector to stick.
There is a slight orange peel on mine, no biggie.
The fit is really accurate indeed.
I had small bubbles for an entire week before it completely disappeared.
Overall, I recommend this skin to anyone who prefers wet applications.
Hey All,
I was asked to review the Exo Skin by Xgear. I requested the White Carbon skin and I have to say it looks great on my black S5! I only have the back installed as I have the Skinomi Tempered Glass Screen Protector on the front. Installation was quick and painless. Literally just place the skin where you'd like it to be and take a hair dryer to it. This helps it conform to the phone and adhere to it. The skin is made from 3m film and has a nice texture to it. You can feel the ridges from the "carbon fiber". I haven't been able to test durability yet and my phone probably wont get a real good test as I typically keep my phone in a case. However, I do think this would stop small scratches and the like whenever I do have the phone out of its case.
I'll get some pictures up tomorrow. I took some on my old phone but lost them like an idiot when I was doing a factory reset for my Gma
Have anyone tried DBrand skin of Note7?
And how are the edges doing? Are they peeling off?
I like the stone/concrete texture. Is it smooth/plastic feel, or like real semi-gloss concrete?
What about metal? Are the titanium strips bumpy or just printed texture?
What about wood? Or Matte?
*Extra question: Is sandstone case available for Note 7 yet?
Bump. Brah
I currently on a s7 edge dbrand skin. I would think the note 7s dbrand skin would be a little similar. I have the matte on the front and back. Fits perfectly and it wraps around the edge perfectly. My front skin actually covers up the front buttons so I can't even see them when they light up.
I have the carbon fiber back only. Fits perfect and has not peeled or bubbled at all. Fit is to the nanometer, so it took a couple tries to align it right. Follow online video instructions. Very happy with it! Carbon fiber gives it a little texture to give it some better grip. Note 7 ATT black.
Thanks guys.
I really like the concrete one. But im not sure if the grip feeling is 80% like real polished concrete or not. I dont dare to order if im not sure because order to my country is expensive AF. Couldnt find a good concrete review on YT.
Now im looking forward to the titanium ones. Does anyone know if those strips texture bumpy 3D or just printed?
I got the mahogany just to cover the back and protect from scratches. When it's out of the case the corners catch on my palm, when I had a slickwraps skin on my S7E it was a perfect fit. This isn't as smooth and you can tell the difference on the edge because it's too thick.
As for the texture it does have a smooth wood type finish. Not quite raw tree bark, but you can feel it as you pass your finger over.
ESR reached out to me to see if I wanted to test any of their new Pixel 4XL accessories so of course I said yes. I'm using their tempered glass case on my 3XL and really like it, and it is good to see that they expanded their lineup for the 4XL. They sent the tempered glass case (Mimic) and protectors, the slim clear case (Zero,) as well as the kickstand case in both clear and black. The cases are all TPU based so they are flexible, and of course the Mimic has a tempered back which adds some rigidity. Since the Nexus 6P I've had a white phone and to show off the color always preferred the TPU sides with a polycarbonate back, but I've found that the glass back is even better in terms of clarity and scratch resistance. While no better or worse than polycarbonate, the smooth back of the Mimic does make it slipperier if you set it down on an angled surface (say, your leg) while the full TPU cases offer just a bit of grip to keep it in place better. All of these ESR cases use what seems to be good quality TPU with the dot matrix pattern to avoid the case sticking to the phone. I was actually impressed that the Mimic offered that, despite only having TPU edges. The "black" kickstand case is more of a smoke color and is semi-transparent. Not sure how well it will pair with the orange or white Pixel 4, but I've got an orange coming so I'll update with pictures once it arrives. The screen protector comes in a two pack and appears to be full adhesive, despite the black border. The sensor areas aren't cut out, but they don't have any adhesive. Time will tell if those areas become dust magnets or not. Obviously without a phone I'm not using them yet, but at least initially the coating feels very smooth.
In the images you're looking at, from left to right, the kickstand case, the Mimic and the Zero. My 3XL has the Zero on, with the 4XL Zero next to it for comparison.
I will of course update this post once my phone arrives, but I know that some of you will start getting phones in the coming days and wanted to throw out my initial opinions. They're offering XDA users a 20% discount with the codes below, and some of the Pixel 4 cases may have a 5% discount on the Amazon page which will stack if available.
Pixel 4XL
Metal Kickstand Case, Clear F8R72K6O
Essential Zero Soft TPU Case, Clear 4X7NAEF8
Mimic Series Tempered Glass Case, Clear 99TV34ZG
Tempered-Glass Edge-to-Edge Screen Protector, 2-Pack ZZNHDQYA
Pixel 4
Metal Kickstand Case, Clear YYEWIX3H
Essential Zero Soft TPU Case, Clear F2N6DUNN
Mimic Series Tempered Glass Case, Clear UI6GFPSP
Tempered-Glass Edge-to-Edge Screen Protector, 2-Pack 46HGDZ9O
View attachment 4851421
View attachment 4851419
View attachment 4851423
View attachment 4851425
View attachment 4851427
View attachment 4851429
View attachment 4851431
Thanks for the codes.
I had already ordered the mimic and essential zero for my (to be delivered tomorrow) 4xl and actually received them yesterday.
I immediately reordered at the discounted prices and initiated the free returns to amazon.
I know it's only a savings of approximately $5.50, but it's definitely worth it to me and I'm happy about it.
Hopefully the cases fit great on my new phone. I want to show off my "panda".
Thanks again
I have the zero clear here waiting for the phone to arrive tomorrow and I just ordered the clear with kickstand and used coupon code. Thanks
Just ordered the mimic. I like the idea of it. We'll see how they execute.
P4XL arrived today, here are pictures of the Mimic, Kickstand (in black) and Zero (in that order) as well as the installed screen protector. I don't think I'm crazy about the screen protector; it went on easily and looks good at a distance, but on dark screens you can see a slight halo around the edges of the display just before the protector's black border. It also feels nice and smooth, but smudges pretty easily.
As for the cases, unlike the P3 the Mimic has a lip where the glass meets the TPU on the back, which gives it just a little grip. I like it. The black Kickstand case definitely would work best on the black, if you're going white or orange I'd suggest the clear case. The Kickstand itself is very sturdy and stays in place at any angle you place it. It has enough strength to prop up the phone with the kickstand lying flat on the table, meaning you can adjust the phone at any angle you'd like. It also adds a pretty sizable hump to the bottom, fwiw. The Zero feels nice and slim, though I'm not sure it's noticably slimmer than the Mimic. The full, smooth TPU gives it a different in hand feel for sure and more grip when laid down on a smooth surface.
All in all I like all 3 cases, but personally I'll probably stick with Mimic. I'll also likely try some other screen protectors, though I can't say any Pixel has had good screen protector options.
View attachment 4853807View attachment 4853809View attachment 4853811View attachment 4853813View attachment 4853817View attachment 4853815
I purchased the zero but haven't put it on yet. This phone feels really good in the hand and I want to go naked.
Sent from my Pixel 4 XL using XDA Labs
kellybrf said:
ESR reached out to me to see if I wanted to test any of their new Pixel 4XL accessories so of course I said yes. I'm using their tempered glass case on my 3XL and really like it, and it is good to see that they expanded their lineup for the 4XL. They sent the tempered glass case (Mimic) and protectors, the slim clear case (Zero,) as well as the kickstand case in both clear and black. The cases are all TPU based so they are flexible, and of course the Mimic has a tempered back which adds some rigidity. Since the Nexus 6P I've had a white phone and to show off the color always preferred the TPU sides with a polycarbonate back, but I've found that the glass back is even better in terms of clarity and scratch resistance. While no better or worse than polycarbonate, the smooth back of the Mimic does make it slipperier if you set it down on an angled surface (say, your leg) while the full TPU cases offer just a bit of grip to keep it in place better. All of these ESR cases use what seems to be good quality TPU with the dot matrix pattern to avoid the case sticking to the phone. I was actually impressed that the Mimic offered that, despite only having TPU edges. The "black" kickstand case is more of a smoke color and is semi-transparent. Not sure how well it will pair with the orange or white Pixel 4, but I've got an orange coming so I'll update with pictures once it arrives. The screen protector comes in a two pack and appears to be full adhesive, despite the black border. The sensor areas aren't cut out, but they don't have any adhesive. Time will tell if those areas become dust magnets or not. Obviously without a phone I'm not using them yet, but at least initially the coating feels very smooth.
In the images you're looking at, from left to right, the kickstand case, the Mimic and the Zero. My 3XL has the Zero on, with the 4XL Zero next to it for comparison.
I will of course update this post once my phone arrives, but I know that some of you will start getting phones in the coming days and wanted to throw out my initial opinions. They're offering XDA users a 20% discount with the codes below, and some of the Pixel 4 cases may have a 5% discount on the Amazon page which will stack if available.
Pixel 4XL
Metal Kickstand Case, Clear YYEWIX3H
Essential Zero Soft TPU Case, Clear F2N6DUNN
Mimic Series Tempered Glass Case, Clear UI6GFPSP
Tempered-Glass Edge-to-Edge Screen Protector, 2-Pack 46HGDZ9O
Pixel 4
Metal Kickstand Case, Clear F8R72K6O
Essential Zero Soft TPU Case, Clear 4X7NAEF8
Mimic Series Tempered Glass Case, Clear 99TV34ZG
Tempered-Glass Edge-to-Edge Screen Protector, 2-Pack ZZNHDQYA
View attachment 4851421
View attachment 4851419
View attachment 4851423
View attachment 4851425
View attachment 4851427
View attachment 4851429
View attachment 4851431
Click to expand...
Click to collapse
Did you know that you have the links grouped and labeled incorrectly? The top group of links says Pixel 4XL - but they are actually for PIXEL 4 products and the bottom group is labled Pixel 4 while the links are all for 4 XL products? Hopefully everyone clicking the links looks carefully before buying anything - or they will be disappointed - I thought you might want to update the OP .....thanks for the options though - look like great products....
Just now I order " Mimic Series Tempered Glass Case " I don't like to use the case all the time. I am a fan of clear full body skin. But I like the idea of the glass case and I am very interesting to try it
Sent from my Pixel 2 using Tapatalk
Geekser said:
Did you know that you have the links grouped and labeled incorrectly? The top group of links says Pixel 4XL - but they are actually for PIXEL 4 products and the bottom group is labled Pixel 4 while the links are all for 4 XL products? Hopefully everyone clicking the links looks carefully before buying anything - or they will be disappointed - I thought you might want to update the OP .....thanks for the options though - look like great products....
Click to expand...
Click to collapse
I did not, thanks and fixed!
Here's some pics of the zero on the 4 xl. It's a good case. The cutouts are lined up good and it's not too bulky. It also has the dot matrix so you don't have spots where it sticks to the phone. Definitely a good case but the phone feels so good naked, I don't think I'll leave it on very long.
Sent from my Pixel 2 XL using XDA Labs
kellybrf said:
I did not, thanks and fixed!
Click to expand...
Click to collapse
I wasn't paying attention and bought the pixel 4 version of the case because of that. No biggy, just made me laugh when I opened the packaging and went to put it on. Refund started and correct one ordered.
The screen protector is really great. Cant tell its on.
What happened to the Mimic black?
I'm using mimic clear currently on my 4xl and it's very nice. With the coupon code and prime discount I paid about $14. Really good deal. Paid about $7 for the essential zero but haven't messed with that one yet.
Sent from my Pixel 4 XL using Tapatalk
Wasn't a fan of the screen protector. Super easy to put on and it doesn't block any sensors. But the rounded corners come out too far cutting of a little bit of real estate. And it holds on to fingerprints so keep a cloth handy. Frustrating as they mailed everything else.
Bought the ESR screen protector 2-pack and it didn't go well for me at all. First one didn't apply properly so had to bin that one, second one spontaneously shattered within 2 days. Got a Spigen one and no issues yet.
So I got the ESR Mimic case and I have to say it's a piece of crap. It's like a 99 cent TPU case with a piece of tempered glass glued protector glued to the back. Mine came in with a bunch of scratches and scuffs that couldn't be buffered off. No point in using a clear case when there's visual imperfections that take awake from the viewing experience. I bet they make a huge markup on this case considering they're charging $22 and that's with the discount. I'm pretty sure they paid for their reviews on Amazon. Returned the same day. Go for the Caseology Skyfall instead it's $14 and a way more attractive/high quality case. It doesn't have a glass back but it is leaps and bounds ahead of the ESR Mimic in terms of quality. https://www.amazon.com/gp/product/B07VFSBQDH/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1
Hey everyone. Been seeing a few threads here with folks struggling with tempered glass screen protectors for the Pixel 4 XL, so I thought I would share what I can about my experiences so far.
Some notes:
- been using this since beginning of November
- I included pictures of two of the cases I have so that you can see the lip, but I also used this with an unpictured Spigen Neo Hybrid and the protector worked fine
- if you want a cheap alternative, the OMOTON was OK but I had touch issues along the edges. Here is a link if you want to check it out (had great coverage the and install tray worked great): https://www.amazon.ca/OMOTON-Google-XL-Screen-Protector/dp/B07VCJHS76
- I am very picky
- webpage for the model I am reviewing below: https://www.zagg.com/en_us/glass-elite-pixel-4-xl
- pictures taken with my old 2XL as best as I could.
- I have not dropped my phone yet thankfully.
Summary:
- this is the best protector I have found so far. I would prefer a Whitestone Dome but I don't think they are making one for the 4XL (based on a response I got from the Amazon store).
- I suggest this protector if you want full coverage* (see review below) and full adhesive and you don't mind spending extra cash. Install is easy with included install tray.
Pros of this protector:
- was available locally at Best Buy and if I didn't like it, I could easily return it.
- is what I would consider full coverage. I don't get any weird reflections on the sides and the screen is not cutoff. If I look at the phone from an extreme angle on one side I can see the image get distorted due to the glass edge lining up perfectly with the AMOLED screen edge, but that's not something that happens in everyday usage. I have pictures of this below. The screen protector lines up perfectly with the lit portion of the screen.
- full adhesive
- no black bars or screen cutoffs. Full clear.
- I got some bubbles when i installed it. They were gone by the next day.
- I had slight touch sensitivity on one side on the first day of install, but it went away by the next day. Sensitivity is as good now as no protector.
- has install tray
- fits the three cases I tried with it; NOMAD rugged leather case, Spigen Liquid Air, and Spigen Neo hybrid. There is still a bit of lip around the sides that allows you to place the phone face-down no problem, and I can swipe with my thumb from the sides of the case to the protector and it does not feel sharp, etc.
Links to the cases I have used here:
https://hellonomad.com/collections/pixel-4/products/rugged-case-black-pixel-4-xl
https://www.spigen.com/collections/...l-4-xl-case-neo-hybrid?variant=30271183880239
https://www.spigen.com/collections/...l-4-xl-case-liquid-air?variant=30271175983151
Cons:
- expensive. I paid $40CDN
- oleo-phobic coating did not last very long. Much better on the Whitestone Dome Glass I had on my 2XL.
- no room for error installing. The screen lines up perfectly with the lit screen, so you need to take your time installing, even with the tray.
- little/no protection at the top.
Some pictures below, with side and front pictures of the Nomad and Liquid air cases.
$40? That's ridiculous. No thanks
Looks like there's some halo in pictures #2 and #5 on the upper left side. Zagg really is too expensive for what they offer especially when it's a one and done. Would be nice to have whitestone but they had a bunch of issues with with the 3/3XL. They cheapened their loca so there was tons of spider webbing and lifting for many.
zetsumeikuro said:
Looks like there's some halo in pictures #2 and #5 on the upper left side. Zagg really is too expensive for what they offer especially when it's a one and done. Would be nice to have whitestone but they had a bunch of issues with with the 3/3XL. They cheapened their loca so there was tons of spider webbing and lifting for many.
Click to expand...
Click to collapse
I had to turn the phone in such a way to get the halo noticeable, ,but yes, in this price range I would have preferred the Whitestone for 100% sure.
This top with no protection bothers me extremely.
This picture isn't very good but these fit great with no halo at all. You get 3 in a pack and it also comes with an installation tray. This one has been on for 2 month and they're only $8.99 for the 3 pack.
https://www.amazon.com/gp/product/B07YCBZCP3/ref=ppx_yo_dt_b_asin_title_o08_s01?ie=UTF8&psc=1
airmaxx23 said:
This picture isn't very good but these fit great with no halo at all. You get 3 in a pack and it also comes with an installation tray. This one has been on for 2 month and they're only $8.99 for the 3 pack.
https://www.amazon.com/gp/product/B07YCBZCP3/ref=ppx_yo_dt_b_asin_title_o08_s01?ie=UTF8&psc=1
Click to expand...
Click to collapse
hate that there is no top protection.. It doesn't feel complete
ceelos218 said:
hate that there is no top protection.. It doesn't feel complete
Click to expand...
Click to collapse
I doubt you'll find one that does, the Soli sensor doesn't work very well through a screen protector. Most protectors also don't cover the camera.
airmaxx23 said:
I don't you'll find one that does, the Soli sensor doesn't work very well through a screen protector.
Click to expand...
Click to collapse
I meant for there to be cutouts instead. I'm waiting for intelliglass 3rd revision for their tempered glass at the moment. it covers the full screen ?
ceelos218 said:
I meant for there to be cutouts instead. I'm waiting for intelliglass 3rd revision for their tempered glass at the moment. it covers the full screen
Click to expand...
Click to collapse
Gotcha, I just don't like the feel of the little tabs of glass with the little cutouts at the top.