The case is great folks and it really changes the whole phone. Much higher quality and physically changes the entire phone.
Video review.
https://www.youtube.com/watch?v=nXZUHeX8ZPI
Link to purchase.
http://www.aliexpress.com/item/New-...red-Glass-Back-Battery-Cover/32456890065.html
Leader2light said:
https://www.youtube.com/watch?v=nXZUHeX8ZPI
http://www.aliexpress.com/item/New-...red-Glass-Back-Battery-Cover/32456890065.html
The case is great folks and it really changes the whole phone. Much higher quality.
Click to expand...
Click to collapse
Isn't the phone slippery? I see a very clear backing, easy gliding out of your hand?
Is it easy to take off the cover?
What's with signal strength? Is it the same as in original plastic cover?
It looks like its higher quality, but it doesnt feel the same. I've had it for 3 months now. Key findings:
-makes your phone thicker, which isnt necessarily bad cause it actually protects the camera, camera doesnt stick out anymore and isnt prone to scratching
-back housing extremely easy to scratch/damage
-smudges easily
-fit and finish isnt really good. it squeaks on places, even though it fits fine
It doesnt make the phone slippery, however a few mm of thickness might make it too big to hold compared to stock cover, at least thats my experience. it works pretty much the same as the original cover.
And despite the rant, I'm still using it. It just makes the phone look cool ^^
Oh yeah and the most important thing
I ordered 3 of those. 2 of them were flawless, however one case had a tad thicker al frame, so when you try to plug your headphones in, you get a distorted sound cause it doesnt really go all the way in. youll need to drill it and widen the hole a bit
asalt said:
Is it easy to take off the cover?
What's with signal strength? Is it the same as in original plastic cover?
Click to expand...
Click to collapse
Signal seems the same. No it is not easy to remove the cover. Much more difficult than the original to remove. Good or bad depending how often you remove back cover.
grox said:
Isn't the phone slippery? I see a very clear backing, easy gliding out of your hand?
Click to expand...
Click to collapse
No, not at all.
sikica133 said:
It looks like its higher quality, but it doesnt feel the same. I've had it for 3 months now. Key findings:
-makes your phone thicker, which isnt necessarily bad cause it actually protects the camera, camera doesnt stick out anymore and isnt prone to scratching
-back housing extremely easy to scratch/damage
-smudges easily
-fit and finish isnt really good. it squeaks on places, even though it fits fine
It doesnt make the phone slippery, however a few mm of thickness might make it too big to hold compared to stock cover, at least thats my experience. it works pretty much the same as the original cover.
And despite the rant, I'm still using it. It just makes the phone look cool ^^
Oh yeah and the most important thing
I ordered 3 of those. 2 of them were flawless, however one case had a tad thicker al frame, so when you try to plug your headphones in, you get a distorted sound cause it doesnt really go all the way in. youll need to drill it and widen the hole a bit
Click to expand...
Click to collapse
Nice review. Its not perfect, but better than the cheap original cover.
It really is a cool way to basically change the entire phone physically.
signal has dropped a bit on mine and this is not as good getting rid of heat I have noticed.
Did anyone find a more rubbery/sticky backcover replacement? I've got the original black one and it's way too slippery.
433Mhz said:
Did anyone find a more rubbery/sticky backcover replacement? I've got the original black one and it's way too slippery.
Click to expand...
Click to collapse
http://www.aliexpress.com/item/New-...dmi-Note-2-Mobile-Phone-back/32522061373.html
There are cases that fit what you need, but battery cover replacements are nicer.
Leader2light said:
Signal seems the same. No it is not easy to remove the cover. Much more difficult than the original to remove. Good or bad depending how often you remove back cover.
Click to expand...
Click to collapse
Of course it drops ! There's so many test in Google Play Store. Just a hint - make a screenshot of some GPS Test app (that shows the signal bars with digits). I had such a aluminum frame (mine is without a back, uses the original, but is very nice) and made a tests. GPS signal drops with about 6-7 ... still not bad, but is excellent without metal frame. The voice quality also drops and makes problems in areas with bad connectivity. The Wi-Fi seems less affected (made no tests).
Sorry man, I'm rarely so harsh, but this thread is VERY misleading, not to say something worse. Yes - aluminum frames are very cute, but on high price - the connectivity. That's why my cute frame gathers the dust, don't use it anymore . One more thing - tried to touch the bottom of two other phones (Xperia Z3 compact is one of them) with such metal frame and GPS signal drops even more drastically . That means that the metal frames are such a sh*t (sorry for the ugly word) !
Let me write about the second "great" back cover replacement - the "leather" one. The "leather" itself is fine - makes a good grip, very hard to drop the phone. But the frame's plastic is extremely soft - my keys made deep scratches on it. Now is ugly one. But the signal remains untouched. Thats why I'll return the stock back cover as soon as my purchased hard case comes.
Related
Figures they'd come out with it a week before I'm thinking of picking up an Imate Ultimate 8150. But it's out for those of you interested link below.
P3600 Full Body Invisible Shield
http://www.shieldzone.com/item_description/HTCP3600I.html
Nice!! It's listed for the P3600i, but I guess it's exactly the same as the P3600.
Anybody tried it already?? Better than a regular silicon cover?
How does this work?
If it is stretched all over the PDA, how is it joined/sealed? What about removing the batter cover or using the thumb wheel? Is it fixed like cling-film?
Also, the screen is recessed from the surround so if it is stretched around the housing and screen, then there would seem to be a gap between the screen and this cover, so what will the sensitivity of the screen be like?
PaulusUK said:
How does this work?
If it is stretched all over the PDA, how is it joined/sealed? What about removing the batter cover or using the thumb wheel? Is it fixed like cling-film?
Also, the screen is recessed from the surround so if it is stretched around the housing and screen, then there would seem to be a gap between the screen and this cover, so what will the sensitivity of the screen be like?
Click to expand...
Click to collapse
If you followed the link and watched the installation video showing it being applied to an ipod you wouldn't have asked.........suggest you try that first.
Andych said:
If you followed the link and watched the installation video showing it being applied to an ipod you wouldn't have asked.........suggest you try that first.
Click to expand...
Click to collapse
looks like it would be a least 3 pieces - one for the screen, then one for the keys, and one for the back - which does not protect the sides. And the video doesn't show how it fits on the phone, it shows how it fits on the front of a ipod - so don't be a smart a*s. He was asking how it fits on this phone not an ipod dumb a*s.
earl00 said:
looks like it would be a least 3 pieces - one for the screen, then one for the keys, and one for the back - which does not protect the sides. And the video doesn't show how it fits on the phone, it shows how it fits on the front of a ipod - so don't be a smart a*s. He was asking how it fits on this phone not an ipod dumb a*s.
Click to expand...
Click to collapse
Get life....yes the clip shows it being fitted to an ipod......if you gothered to watch the clip you would have seen that the piece for the back also does the sides as they wrap around.....apart from the size etc the actual method of applying this will be the same.
Next time smart a*s do your homework rather than mouthing off.
Oh yes all my questions answered if only I had watched the ipod video.
Now All I need is an m700 that is exactly the same shape as an ipod, with all the buttons in the same place, with a flush screen, and well, all very ipodish, and then it will all be clear.
So this will be no more than a screen protector on the PDA. It will not protect the buttons or lower raised section of the housing. Also won't protect the sides (too many buttons), and it seems that the tight curves will be a problem for this cover. I can see this peeling off the m700 in a very short time
If you know so much about it, then can you explain how it will work with a recessed screen? Will I be able to tap it all over with a key and not damage the phone, and if I throw it in a box of coins, will all the phone be safe from scratches and chips - just like the ipod?
PaulusUK said:
Oh yes all my questions answered if only I had watched the ipod video.
Now All I need is an m700 that is exactly the same shape as an ipod, with all the buttons in the same place, with a flush screen, and well, all very ipodish, and then it will all be clear.
So this will be no more than a screen protector on the PDA. It will not protect the buttons or lower raised section of the housing. Also won't protect the sides (too many buttons), and it seems that the tight curves will be a problem for this cover. I can see this peeling off the m700 in a very short time
If you know so much about it, then can you explain how it will work with a recessed screen? Will I be able to tap it all over with a key and not damage the phone, and if I throw it in a box of coins, will all the phone be safe from scratches and chips - just like the ipod?
Click to expand...
Click to collapse
Lets get this straight....I haven't used this product...however when I saw the "link" I went to the manufacturers site to get a better understanding of it....
I watched the video and while it was of it being fitted to an ipod I got a basic understanding of how it could be fitted to a P3600i.
I didn't think it was "cling wrap", I understood that there would be several sections involved....including one for the recessed screen (yes, just like a normal screen protector) and I too would be skeptical of it protecting all parts of the phone.
There is a tendency in these forums for people to not search out information but to ask seemingly dumb questions.....
As this product is new for this model....why not just ask if anyone has tried it or ask the manufacturer for more information.....or is that too hard to do????
NOT FULL BODY...JUST SCREEN ONLY
The site says full body not Screen only, that's a separate option...
I would really like to know if and how exactly this works on 3600.
I actually have silicon case and screen protector for mine, but this would make it considerably smaller...
Bought and use the InvisibleShield
Folks,
I bought it and had it send to Holland. Took about 1 to 2 weeks but ok I am not in a hurry.
The full body covers basically all the shiny black plastic plus the screen. The rest (middles of the sides and the front keys) are not covered. Also offcourse the camera, speakers etc are not covered. However, and this is probably the difference between P3600 and P3600i the front camara is covered by the shield blurring the image. Now I have already put it on the camera but the next time I would use a hole puncher to add the extra hole. I probably will use a sharp hobby knife to cut an extra hole (on the other hand I never use video conferencing).
The plastic is more stronger and thicker then normal screen protectors. Haven't tried to scratch it on pupose and guess what I am not going to do it. If a scratch forms by accident I will mention it here.
The screen takes some getting used to with the new cover. The plastic does not "slide" as easy as the original screen protector or the screen itself. Maybe this is just in the first period.
The application process it pretty easy if you just take the time. Takes about 30 minutes if you do it slowly. Only 2 minor bubbles on the back but those are not really an issue, the rest is perfect.
Hey for 20 euro's I think it is a good deal. No horrible rubber case or GPS blocking metal case for me anymore. Only downside is that if the phone is dropped now there is no protection. This is only against scratches.
Lifetime guarantee so lets see how often I have to send it back.
All in all recommended so far (but that is just after 1 day of use)
I want to see it
Post a picture please
Isn't it invisible?..
See the invisible sheet
Well actually it is quit difficult to see but here are some picures. The picture from the side shows you some edges.
Edges
The edges that you can see in the pic don't seem to line up perfectly, how were the dimensions on the rest of the edges?
i've been thinkin of getting one of these since i saw them for ipods but that messy edge is scaring me away a little, also how are you finding the screen protector after a little more use?
Edges reply
Well the edges are more because of my talent I think. The reason why I showed you this is because at least you can see something. For the rest it alligns perfectly.
After using it for a while it still seems a great product. I accidentaly dropped the thing but no scratch at all. What you do notice is the slightly more pressure you need when using the stylo. Also the screen protector is not as smooth as the original screen making the sliding a little more difficult. Also the plastic sticks to your ear while calling. But all in all still recommended.
I just put it onto the white one...
...and it is invisible. You can see it only on buttons' silver surrounding, on white parts only the edges are visible if you try really hard. I haven't got a good enough camera to show it, sorry.
It has a sticky feeling about it (maybe needs to dry more?). I don't like it on the screen - feels sticky and thick. I'd say use a decent screen protector instead.
It came WITH the cut-out for a camera (it's 3600i shield, I've got 3600), so it fits like a glove.
Oh, it's not a stress-free, low pressure 15 minutes application like they advertise it. It's fekkin pain in the ar$e one hour job, you're swetting your ar$e off. And - I guess - you can never get it perfect at the end. There will always be a bubble or misaligned edge somewhere (or is it me?).
Long term use review to follow.
sabestian said:
...and it is invisible. You can see it only on buttons' silver surrounding, on white parts only the edges are visible if you try really hard. I haven't got a good enough camera to show it, sorry.
It has a sticky feeling about it (maybe needs to dry more?). I don't like it on the screen - feels sticky and thick. I'd say use a decent screen protector instead.
It came WITH the cut-out for a camera (it's 3600i shield, I've got 3600), so it fits like a glove.
Oh, it's not a stress-free, low pressure 15 minutes application like they advertise it. It's fekkin pain in the ar$e one hour job, you're swetting your ar$e off. And - I guess - you can never get it perfect at the end. There will always be a bubble or misaligned edge somewhere (or is it me?).
Long term use review to follow.
Click to expand...
Click to collapse
Any update to report? I'm thinking about buying one and would like your oppinion since you've now had it for a while.
Dimitri- said:
Folks,
I bought it and had it send to Holland. Took about 1 to 2 weeks but ok I am not in a hurry.
The full body covers basically all the shiny black plastic plus the screen. The rest (middles of the sides and the front keys) are not covered. Also offcourse the camera, speakers etc are not covered. However, and this is probably the difference between P3600 and P3600i the front camara is covered by the shield blurring the image. Now I have already put it on the camera but the next time I would use a hole puncher to add the extra hole. I probably will use a sharp hobby knife to cut an extra hole (on the other hand I never use video conferencing).
The plastic is more stronger and thicker then normal screen protectors. Haven't tried to scratch it on pupose and guess what I am not going to do it. If a scratch forms by accident I will mention it here.
The screen takes some getting used to with the new cover. The plastic does not "slide" as easy as the original screen protector or the screen itself. Maybe this is just in the first period.
The application process it pretty easy if you just take the time. Takes about 30 minutes if you do it slowly. Only 2 minor bubbles on the back but those are not really an issue, the rest is perfect.
Hey for 20 euro's I think it is a good deal. No horrible rubber case or GPS blocking metal case for me anymore. Only downside is that if the phone is dropped now there is no protection. This is only against scratches.
Lifetime guarantee so lets see how often I have to send it back.
All in all recommended so far (but that is just after 1 day of use)
Click to expand...
Click to collapse
Same question for you... Any updates? Thank you...
Definately recommended
After using it a few months I still think it is definately worth the few euro's. Ok it sticks a bit when calling for a long time and I think I even managed to get a small scratch on it but I sort of abuse the fact that I have the shield. Store it with keys, never use a case etc.
No I have bought some useless accessoires such as aluminium case (blocks GPS) and the remote for mediaplayer but the shield I would really recommend.
Cheers,
Dimitri.
Like most of us that keep no cover on our phone, my battery plate was all scratched to heck. I saw the other "mirror polish" mod and it looked great, but also looked like a lot of work and would get scratched again. I bought a can of rubberized spray (see pic) and wound up with a great result (see pic.) The only color Home Depot had was black, and I think a gray might have looked better, but I still like the results and the phone is less slippery now than with the metal cover. This took 3 coats (30 minutes drying time between coats) then I let it dry for 18 hours before using it. Turned out pretty good, but long-term results are TBD...
I like did u just spray the back part? Any trouble with fitting it afterwards as it must add a layer of bulk?
Desire Z Glite 2.0.1
Shambolicuk said:
I like did u just spray the back part? Any trouble with fitting it afterwards as it must add a layer of bulk?
Desire Z Glite 2.0.1
Click to expand...
Click to collapse
It added less bulk than I thought it would, it's really not much at all and it fits just fine afterwards. Actually, before, it would slide like a little when locked in place (just enough to notice - probably like .1 mm or so.) Now it is snug and has no jiggle at all.
I forgot to mention the hard part (prepping it...) Removing the original clear plastic coating was the hardest part - a combination of a dremel with the little wire wheel tool and my fingernail took about an hour, then I just hit it with some 220 grit sandpaper and cleaned it with mineral spirits.
I use the same stuff on my car (mid level 2009 Lancer but use the Plasti-dip to black out the front to make it look like an Evo [car guys will understand =p]) Very durable though I have not used it on my DZ yet. You beat me to the punch! I want to do the HTC part in red and the rest in black, will post when I have the time to do it.
Looks sharp though, contrast is nice
Doh! After only 1 day, I caught something on the curved edge and it started lifting the plastic coating... not very durable for this use - I might try again later though and see if I can come up with a better method.
Sent from my HTC Vision using XDA App
I like it! A little bit rougher texture, but you might try Duplicolor spray on bedliner.
I thought about taking my phone apart and using some white plastidip to change it white...
Durability is alright...on thinkpad forums, a couple of people mixed it with some black enamel paint which made it much more durable.
mralexsays said:
It added less bulk than I thought it would, it's really not much at all and it fits just fine afterwards. Actually, before, it would slide like a little when locked in place (just enough to notice - probably like .1 mm or so.) Now it is snug and has no jiggle at all.
Click to expand...
Click to collapse
I thought I was the only one who noticed the battery door wiggle room! No one ever mentions it. I really hope you find some way of preventing it from peeling. I'm practically drooling over those pictures you took. It looks extremely professional compared to most mods I've seen. You could easily set up a service where people send you their doors, some cash, and a self address envelope if you wanted to make some extra bucks.
kierren said:
I thought I was the only one who noticed the battery door wiggle room! No one ever mentions it. I really hope you find some way of preventing it from peeling. I'm practically drooling over those pictures you took. It looks extremely professional compared to most mods I've seen. You could easily set up a service where people send you their doors, some cash, and a self address envelope if you wanted to make some extra bucks.
Click to expand...
Click to collapse
I've been meaning to update this. I tried again - this time I sanded with 220 grit, used a "self-etching primer" on the cover, then the rubberized paint. This time it lasted 3 days before starting to peel off... I'm also able to scratch off the primer with my fingernails, so the primer didn't really help. I'm not sure what else to try to make this coating stick at this point.
mralexsays said:
I've been meaning to update this. I tried again - this time I sanded with 220 grit, used a "self-etching primer" on the cover, then the rubberized paint. This time it lasted 3 days before starting to peel off... I'm also able to scratch off the primer with my fingernails, so the primer didn't really help. I'm not sure what else to try to make this coating stick at this point.
Click to expand...
Click to collapse
I suggest powdercoating the back cover.
primeral said:
I suggest powdercoating the back cover.
Click to expand...
Click to collapse
Powder coating would be nice, but I don't have the equipment for that (and don't want to invest in it just for this.) Also, this cover has plastic tabs that I'd be worried about melting or detaching from the battery cover during the curing process.
Hey everybody, got a new case review. This one is the infamous Nillkin Fresh, which is Nillkin's second generation of flip covers. To be honest, I got this case because it works with the iloome ScreenMate tempered glass protector I got, which didn't work with any of my other cases.
I got the yellow color, and it looks very nice. The flip has a darker yellow than the snap on part, which looks perfectly fine to me. The flip doesn't stay down for the first few days, and it doesn't have a lock mechanism. But, with a few days use, the flap does stay down on itself. Now, at first it wasn't working with my tempered glass protector, so I just kept stretching the fake leather out, and eventually it stays. I just clamped it so it stayed stretched. This is a very simple case, and if you don't drop your phone a lot (like me) this is a really nice case, it has a soft lining on the inside of the flip, almost like micro-fiber, and it helps keep fingerprints away. I do like this case, but it's not perfect. You can also use it as a stand, just fold it back and slide it into the slot. I absolutely HATE this feature, as the slot sticks out from the back of the case, so I can't use it with the Orb Charger. I forgot to take pictures of it, but it is REALLY annoying. Overall, aside from that one thing, it's a really nice case. :laugh:
Just to add on to OP, mine's the light blue one, a really sweet colour.
Has a microfiber (or whatever you call that) lining, prevents the screen from getting scratched.
The thickness. When paired with apps like Proximity AutoLock. you simply flip the cover and BAM, the phone locks itself. (Disclaimer: The app takes up quite a lot of battery though.)
Thickness again.
Thickness compared to a bumper. (if you haven't realized yet, I like blue )
The back plastic has got this pearly, glittery effect, too subtle to notice unless you're staring at it.
The front is a leathery kind of texture. Not real leather, of course.
It does destroy the edge swiping experience, with the exception the left hand side center (shown in the pic). May cause full screen SPs to bubble up too, but I have no idea, I don't use full screen ones.
How it looks. Mine has yet to become seasoned, so it'll topple if I don't support it. It has a hook that'll hook the front cover.
The headphone jack.
Those with a dbrand skin might want to take note, it kinda leaves a mark on the skin, but if you don't use the case for long enough, the mark'll go away.
I'd recommend it 8/10 overall as it makes it hard to use the phone using your left hand with the front flap, also, it makes my phone feel like a tank. But the front protection is great if you're not using a screen protector. But be careful of oil stains, they're almost impossible to remove from the inner lining. Washed it once, dried it and it feels like new again.
Edit, does anybody know how the hell do I resize the pictures? They're HUGE.
jiayit said:
Just to add on to OP, mine's the light blue one, a really sweet colour.
Has a microfiber (or whatever you call that) lining, prevents the screen from getting scratched.
The thickness. When paired with apps like Proximity AutoLock. you simply flip the cover and BAM, the phone locks itself. (Disclaimer: The app takes up quite a lot of battery though.)
Thickness again.
Thickness compared to a bumper. (if you haven't realized yet, I like blue )
The back plastic has got this pearly, glittery effect, too subtle to notice unless you're staring at it.
The front is a leathery kind of texture. Not real leather, of course.
It does destroy the edge swiping experience, with the exception the left hand side center (shown in the pic). May cause full screen SPs to bubble up too, but I have no idea, I don't use full screen ones.
How it looks. Mine has yet to become seasoned, so it'll topple if I don't support it. It has a hook that'll hook the front cover.
The headphone jack.
Those with a dbrand skin might want to take note, it kinda leaves a mark on the skin, but if you don't use the case for long enough, the mark'll go away.
I'd recommend it 8/10 overall as it makes it hard to use the phone using your left hand with the front flap, also, it makes my phone feel like a tank. But the front protection is great if you're not using a screen protector. But be careful of oil stains, they're almost impossible to remove from the inner lining. Washed it once, dried it and it feels like new again.
Edit, does anybody know how the hell do I resize the pictures? They're HUGE.
Click to expand...
Click to collapse
You could just use a photo editor and re-crop?
Sent from my Nexus 4, the only phone approved by Patrick Star
N4ever said:
You could just use a photo editor and re-crop?
Sent by a giant douche
Click to expand...
Click to collapse
While we're doling out advice, I recommend that you change the text you quote so everyone doesn't have a second column of gigantic images...
N4ever said:
You could just use a photo editor and re-crop?
Sent from my Nexus 4, the only phone approved by Patrick Star
Click to expand...
Click to collapse
You could have said that without quoting the images all over again....
I have this case too, just never got around to finish writing my review. Mine is mint green (though some product pictures may appear turquoise).
Having a front cover in addition to the case is definitely nice, as I can drop it into my bag without worrying about what is going to hit against the front screen. Also very handy when talking on the phone with the flap covering the screen.
It's not slim as a ringke slim but not thick either, and the phone looks nice in it. I liked that it didn't have an actual lock to keep the cover on because it was easier to flip open.
It's so annoying when your holding it open. No comfortable way to do it.
Sent from my Nexus 4, the only phone approved by Patrick Star
Are the buttons easy to press?
Sent from my Nexus 4 using Tapatalk 4 Beta
Tbh it's quite hard. And trying to take a screenshot with both buttons is a nightmare. But I don't take that many screenshots anyway and the power button is not really that hard to press, it's just that their opening hole for the power button is a tad too small.
jiayit said:
Tbh it's quite hard. And trying to take a screenshot with both buttons is a nightmare. But I don't take that many screenshots anyway and the power button is not really that hard to press, it's just that their opening hole for the power button is a tad too small.
Click to expand...
Click to collapse
I can see the volume rocker is exposed when you open the case. The power button looks a bit hard. In my current case(looks like the ringke slim) i had to cut off the bar at the top to gain easy access to power button.
Sent from my Nexus 4 using Tapatalk 4 Beta
The way everything folds is just uncomfortable.
Sent from my Nexus 4, the only phone approved by Patrick Star
I got this case last week, black one. The plastic base is super cheap, there are at least two defects and the frame around the power button is simply bent. Although my flip cover actually rests perfectly on the screen, the plastic part makes noises everytime a little pressure is applied to the sides.
Went straight to the litter bin, I'd rather use my phone naked than inside this thing.
Just my two cents.
Fabriciohss said:
I got this case last week, black one. The plastic base is super cheap, there are at least two defects and the frame around the power button is simply bent. Although my flip cover actually rests perfectly on the screen, the plastic part makes noises everytime a little pressure is applied to the sides.
Went straight to the litter bin, I'd rather use my phone naked than inside this thing.
Just my two cents.
Click to expand...
Click to collapse
Seems like you got a manufacturing defect.. Why didn't you ask for a refund?
Hung0702 said:
While we're doling out advice, I recommend that you change the text you quote so everyone doesn't have a second column of gigantic images...
Click to expand...
Click to collapse
Sent by a bigger douche who calls people out
Sent by an even bigger douche
Sent from my Nexus 4, the only phone approved by Patrick Star
Item can be found here
http://www.ebay.ca/itm/380903948151?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649
Pics will come later, i just got it in the mail and don't have another camera that i can use. This is the initial first looks
I got this case in the red colour and for 11 dollars, quality is quite impressive, this case came with an allen key (which is required to open and close the case ) 2 extra pentalobe type screws, I'm not sure what their called and a micro fiber cloth.
Many people had complained about signal loss and weaker signals with the case on but i have found no difference, with the case off, my wifi speeds are around 40mbps and with the case on are around the same mark, maybe a couple mbps slower but nothing noticeable, speakers are also just as loud, IR range seems to have dropped significantly because of how thick the case is and how narrow the opening for the blaster is.
It is stated that the case is for splashes only, like a light rain or wet handed usage but I'm not ready to throw my baby into a bucket of water :cyclops:
I will add pics later but from my initial reaction it seems like a great case
Pros:
looks bada$$
great quality
no real signal loss or draw backs
feel like i could safely drop it off the CN tower
Cons:
Heavy as hell
takes a long time to take it on and off, and don't strip the screws or your gonna have a fun time (not) trying to get the screw out to free your phone
some accessories may not work due to much larger size
Hi there,
You could do an easy test to check how waterproof it is. If you could place a dry tissue inside case and drop it into sink full of water maybe :silly:
I will wait for some feedback.
looks sweet but i doubt the waterproof ness. earpiece speaker covered with glass? how can you hear? BTW put a dab of anti seize on the screws.
its not fully waterproof since the camera and flash aren't covered but for calling in the rain etc its great i played a 90 minute game of soccer in heavy rain and my phone was on top of my bag and when i was don't it worked like new, i only really use the case when I'm going fishing or biking etc
i own one of these used it a month and bought the trident kraken ams case for the s4 and love it. The alluminum one is just heavy (i know what ur thinking of how heavy can it be but it really is and u will notice when u take it off and see how heavy it is) there is signal loss not alot but there is so if u live somewhere with bad signal dont get it or u wont have a signal at all. the buttons are a little hard to press. I worry the home button will wear away the way the top button lays on it. The back and menu buttons have to be pressed hard since there conductive. It is definately not waterproof more splash proof. Also its hard to hear people your calling it in. Your speaker is also muffled.
Hope this helps any questions I will answer. :fingers-crossed:
Does anyone know where to find a rubber bumper? I've seen only metal ones.
sent from my MI5
Something like this?
https://www.aliexpress.com/item/For..._9&btsid=e644bdc0-3e04-47b6-8430-2477fd51a6f4
I bought this for my self, and its really good, nice fit,but power and volume butons are little hard to pres...
Marun1982 said:
I bought this for my self, and its really good, nice fit,but power and volume butons are little hard to pres...
Click to expand...
Click to collapse
Yes! I also bought this one. It is very solid and high quality thing, which makes me not to worry about my phone. You can remove plastic piece to put this cover on or off your phone much easier. Very convinient.
Try cocose.
I currently using this case and this is really strong
Sent from my gemini using XDA Labs
I'm using this one and its very good: https://www.aliexpress.com/item/Arm...f-Hard-PC-Soft-Silicon-Cover/32750174762.html
https://www.aliexpress.com/item/Lux...76-4008-9ac8-d12cf3b7b388&transAbTest=ae803_2
Try this. It's the best you can get. A bit heavy, but the phone is light by it's own, so it doesn't end up that bad. What's important is that the plastic is very hard and will probably never break unless you step on it with a car. They use metal for top and bottom, while for the corner it's a mix of metal from the top cover and plastic from the while body, so i guess if you drop it on the corner, the metal part will bend first and then the plastic will absorb the remaining impact and break, that way your phone will be safe. i've been using it for a week and it feels amazing in my hand
All of the above cover the whole back side of the battery, which makes cooling a big problem. Especially when charging and using the phone at the same time, e.g. during car navigation, it gets extremely hot and starts throttling even without a back cover.