Related
Hello,
I have big problem. I tried to upgrade to lollipop version, used it for one hour and then decided to get back to kitkat. For the procedure I used some tool from killerdogKD which name is MT7-L09 Unbrick (it is a fastboot). The procedure went, phone rebooted and got stuck in boot loop (only logo is showed for few seconds). Now I can only get in fastboot and rescue mode. I've tried to flash stock rom, but without success. Any suggestions? PS. Yes, I now I am jackass and sorry for my bad English:angel:
Stock recovery installed (extracted from official KK ROM)??? 3 button procedure already tried?
Will not work. Are there no going back. He can recover only 5.1.
For the people hanging in Bootllop because they have the 4.4.X Recovery flashed.
Load zip, go to the boot loader and the two flash imgs.
command:
fastboot flash boot boot.img
fastboot flash recovery recovery.img
If both of the 5.1.
https://mega.co.nz/#!DNw13JhK!7ATC9p...G50saLGZG3vKzM
KK is not possible 5.1, just with dload the flash 5.1 again. Is indeed just about the one that has 5.1 Recovery again.
Here read next time.
http://forum.xda-developers.com/mate-7/general/mate-7-update-to-lollipop-screenshots-t3125227/page28
I have the same problem and probably caused by same thing. But I can' even enter bootloader. When phone was bootlooping, I turned it off. Then I tried to get into recovery (by holding power + volume down), but phone always shut down after Huawei logo appears (shut down with short vibration).
It does not matter when I release the buttons, I also tried the recovery (vol up + power) or the force update mode (vol up + vol down + power).
Is there any solution to this? I really hope so...
Look at my post and Liks.
Thank you Fooox1 for trying to help, but the problem is, that I can't even enter the bootloader (and your steps require that). I think that international Mate7 have different key combination for entering bootloader? Check also this: http://forum.xda-developers.com/mate-7/help/fastboot-mode-t3086531
It is true that even before I was not able to get into bootloader with vol down + power, so maybe there is just different key combination or it is not possible at all...
I think I will try to write to Huawei support.
In the bootloader you come when the power is off and you Vol - holding down, then to the PC. To turn it off properly you must Vol - and Power button until it vibrates.
Key combination is the same for all.
I know, that is what I am doing it. And I already did it with many other phones successfully, so its not like this is my first time.
I am holding down power + vol down
Phone vibrates, I am still holding both buttons
Huawei logo appears, I am releasing power button, but still holding vol down button
Phone vibrates and turn off
I also tried to release power button when phone vibrates, or not release both buttons at all or I don't know what else. Tried 100x times.
I will try to contact Huawei, maybe it is known issue. It should really be same key combinations for all devices.
Thank you.
The Mate mus but this depend on the USB, otherwise it does not come into the bootloader.
Whoa! I did it. Yes, it was connected in USB, but in quickcharge USB. I tried different one and I am in!
For some reason, it did not like the quickcharge USB port, strange.
@Fooox1: but thank you, with your last comment I got the idea to try different USB
Well, I am little bit furhter, but still not working unfortunately. I got into bootloader, I flashed the boot and recovery. Then I was trying to three buttons force update and it is still failing.
I have Update.zip in dload folder on sd card, but update is failing immediatelly...
So now, I started the three buttons update while connected to computer via USB and it is actually doing something. But it is too soon to say if it helped (43%).
can't boot too
I need your help Guy's
My Mate 7 did not start after i rooted the lollipop rom with kingroot. I tried to put back the 5.1 boot.img and the recovery.img. After that i tried to flash the ota 5.1 rom agian with the 3 bottons mode. The phone startet the Update but it get stocked by 90%. I waited ca. 10 min after i just rebooted the phone. Now the Phone starts with the Huawei Ascend sign two times and after that i am in recovery mode. I don't know what i can do now! Can anyone help me please?
Yes, I have the same problem
driver84 said:
I need your help Guy's
My Mate 7 did not start after i rooted the lollipop rom with kingroot. I tried to put back the 5.1 boot.img and the recovery.img. After that i tried to flash the ota 5.1 rom agian with the 3 bottons mode. The phone startet the Update but it get stocked by 90%. I waited ca. 10 min after i just rebooted the phone. Now the Phone starts with the Huawei Ascend sign two times and after that i am in recovery mode. I don't know what i can do now! Can anyone help me please?
Click to expand...
Click to collapse
Same here! Help!
must we send in warranty?
So it seems to me, that problem is Huawei. Once, they are using Update.APP and later Update.ZIP, not sure why.
- recovery from 5.1 is working, but it is expectin Update.APP, but 5.1 update is in Update.ZIP, so it fails immediately (with error Update.APP not found). Yes, when you connect to phone to computer, it seems that it is doing something and it will get to 90%. But it is actually doing nothing, you can even pull out the sd card and it is the same. I think it is waiting for some action from computer, but not sure which (I also tried to install HiSuite and do something with it, but no success).
- recovery from update B137 will accept Update.ZIP, but when you try to flash it you won't be able to get in it, it is not working (I also tried B127).
So now, we either need recovery, which will work on 5.1 and will accept Update.ZIP or we need update packed as Update.APP (and yes, I tried to rename it etc.). So actually, our phones are pretty ok, we can get in recovery etc., but Huawei is messing with this different formats for some reason
@Fooox1: Do you have any ideas? Maybe you have another bootloader / recovery image? How did you got the 5.1? Thank you...
Edit: maybe the problem is, that we are trying to run the update OTA (Update.ZIP) instead of full rom (Update.APP)? Is this how it is divided, Update.ZIP is just incremental update, while Update.APP is full rom? If that is the case, we will need the full rom, maybe Huawei can release it?
I have not the problem, but users in our forum. I have the boat and recovery.img from the update unzip, a user has then flashed via fastboot and sin device was running again. For him only recovery was gone after he has the Kang Recovery flashed. The Update.zip he did not need to flash.
Other users have only the boot and recovery.img flashed and then the not unpacked update.zip in a folder (dload) on the SD and these then flashed three fingers method. What also has to work.
Here is still the boat and recovery.img of 5.1.
https://mega.co.nz/#!DNw13JhK!7ATC9pAUID0VyX5N3pQwQLbb_VyuOG50saLGZG3vKzM
And update.zip
https://mega.co.nz/#!vdYlxQIA!P34e3RI-hQT1ZY2WnfOosGmkq2wlr6NViq6ehQuWN5k
I think it may help if somebody will create *.img files from Lollipop, then we might be able to flash it via fastboot (the same as it is in this MT7-L09 Unbrick). I think we will need:
boot.img - ok
cache.img
cust.img
recovery.img - ok
system.img
userdata.img
Can make you yourself. Unzip, when present therein Update.app the extension .app in change .zip and unpack. Now you have another Update.app, this you can unpack the Huaweiextraktor, you've got your files. However, it does not contain all IMGs.
You could try but the resulting Update.app to pack in the dload folder and flash. If so, then the original and encrypted.
Hallo again,
i just called the Huawei Service Center in Germany. They openend up a Ticket for me. They told me to make a factory reset and after that the Phone should boot normaly. I did that, but still the same is happening. The shows the Huawei Ascend Logo 2 times and after that i am in recovery mode again.
The only thing i can do next, is to send the phone to the Huawei Service Center and hopefully i will get it back in 7 Days.
Hi guys..hope somebody can help me to get my phone working again..i had lollipop installed and by accident I deleted the internal memory..the only thing what I can is to reboot to recovery twrp..and then on my pc phone shows up..1 cust drive and 1 internal..which is empty..do you have any idea about that? thanks a lot..please help )))
Download the stock rom for your phone model (tl-10) official one, NOT beta version, better directly from Huawei web site.
Extract stock recovery from downloaded file (by using huawei extractor app).
Using ADB commands, flash stock recovery. Then copy stock rom to sdcard and proceede with 3button procedure.
If any of these operations sound new to you, please use "search" button in these forums.
tuddu said:
Download the stock rom for your phone model (tl-10) official one, NOT beta version, better directly from Huawei web site.
Extract stock recovery from downloaded file (by using huawei extractor app).
Using ADB commands, flash stock recovery. Then copy stock rom to sdcard and proceede with 3button procedure.
If any of these operations sound new to you, please use "search" button in these forums.
Click to expand...
Click to collapse
I have downloaded from Huawei web site 120sp04 firmware. I extracted recovery, flashed with adb commands. Copied the stock rom to sd card, and i am not able to force my phone to start update. keeps restarting. is the a special trick for this 3 button procedure? phone should be off, but from bootloader i cannot switch of the phone. Is it possible that the phone doesn't recognize my SD Card? please advise.
Please check, there' s a command trough ADB (I think adb reboot) wich reboot phone.
Then, someone, has been forced to keep the SD card NOT inserted into the phone, waited for reboot and then (after huawei logo I think, but I'm not sure; please check) inserted the SD card.
Then proceede with local update (forced method).
As for the 3button method, simply press and keep pressed volume up+volume down + power on button. All togheter.
Then the phone must boot automatically into recovery and start the procedure itself.
It i clear: stock recovery MUST be already installed !!!
tuddu said:
Please check, there' s a command trough ADB (I think adb reboot) wich reboot phone.
Then, someone, has been forced to keep the SD card NOT inserted into the phone, waited for reboot and then (after huawei logo I think, but I'm not sure; please check) inserted the SD card.
Then proceede with local update (forced method).
As for the 3button method, simply press and keep pressed volume up+volume down + power on button. All togheter.
Then the phone must boot automatically into recovery and start the procedure itself.
It i clear: stock recovery MUST be already installed !!!
Click to expand...
Click to collapse
The only thing what i can do is, to flash recovery and boot from fastboot.zip( http://forum.xda-developers.com/mate-7/help/5-1-to-4-4-2-bootloop-t3132888 ) i guess for L09 version, where i can get to update mode with 3 buttons...all other possibilities are not possible. even if i extract from original firmware recovery and boot images, nothing work..i was going from B125 back to B123 to B128 and B313 when in TWRP i deleted everything. Phone is charging, i can turn it off..OS is missing..is it possible that somebody would make a back up in twrp and i would flash it on my phone? or what version of firmware i should start with? what about sideload? does it help? please advise.
alworth said:
The only thing what i can do is, to flash recovery and boot from fastboot.zip( http://forum.xda-developers.com/mate-7/help/5-1-to-4-4-2-bootloop-t3132888 ) i guess for L09 version, where i can get to update mode with 3 buttons...all other possibilities are not possible. even if i extract from original firmware recovery and boot images, nothing work..i was going from B125 back to B123 to B128 and B313 when in TWRP i deleted everything. Phone is charging, i can turn it off..OS is missing..is it possible that somebody would make a back up in twrp and i would flash it on my phone? or what version of firmware i should start with? what about sideload? does it help? please advise.
Click to expand...
Click to collapse
Hello!
I have similar problems, but i have the L09.
Check if you can mount system. Or if you can wipe system, because i can't
Good luck!
Today I accidently wiped my internal and external sd card from twrp recovery mode. I was on Lolipop 5.1.
As I wanted to install Cyanogenmod Rom I tried to reflash CWM recovery. Ater doing that I was not able to enter the twrp recovery anymore. I had accecs to the unlocked bootloader and tried to reinstall the boot, recovery and system via fastboot but without any success. The phone did not boot and I couldnt enter recovery mode anymrore.
Now I accidently flashed via fastboot a wrong boot and recovery firmware (4.1) and since that I can not even enter fastboot. The pictre shows where I am stuck. On the bootloader page it says:
Error
Func NO: 10 (FUNC_BOOT_RECOVERY)
Error NO: 2
Can somebody help me to repair my device? Its brandnew.
What can I do without a recovery, without a system and without fastboot.
Here is the picture:
hxxp://s21.postimg.org/tqzu1wlhj/IMG_0191.jpg
balpem said:
Today I accidently wiped my internal and external sd card from twrp recovery mode. I was on Lolipop 5.1.
As I wanted to install Cyanogenmod Rom I tried to reflash CWM recovery. Ater doing that I was not able to enter the twrp recovery anymore. I had accecs to the unlocked bootloader and tried to reinstall the boot, recovery and system via fastboot but without any success. The phone did not boot and I couldnt enter recovery mode anymrore.
Now I accidently flashed via fastboot a wrong boot and recovery firmware (4.1) and since that I can not even enter fastboot. The pictre shows where I am stuck. On the bootloader page it says:
Error
Func NO: 10 (FUNC_BOOT_RECOVERY)
Error NO: 2
Can somebody help me to repair my device? Its brandnew.
What can I do without a recovery, without a system and without fastboot.
Here is the picture:
hxxp://s21.postimg.org/tqzu1wlhj/IMG_0191.jpg
Click to expand...
Click to collapse
So (Vol-) + (Power) w/ usb plugged in doesn't bring it to recovery mode? Have you tried with HiSuite?
jfer671 said:
So (Vol-) + (Power) w/ usb plugged in doesn't bring it to recovery mode? Have you tried with HiSuite?
Click to expand...
Click to collapse
No because I had twrp recovery installed and tried to flash cwm over it. After that I had no recovery at all. But I made some progress now... I am able to flash the same newest twrp 2.8.7.0 recovery to the phone and I managed also to flash the 5.1 stock recovery. I flashed BOOT.img from 5.1 and SYSTEM.img from 5.1 and I got rid of the error in fastboot menu.
Stock recovery I can flash via installer_r24.4.1-windows from acbka.
http://forum.xda-developers.com/mate-7/orig-development/tool-android-4-4-5-1-pc-t3186984
And these two recoveries seems to be the only one that work on my phone....? Currently I have stock recovery installed and i put MT7-L09C900B324 on my sd card (dload/UPDATE.app) and did the three buttons rescue. It seemed to work but It stoped at 90% and still no luck. What am I doing wrong this time?
Hi Suite does not recognitze the phone. When I abort the istallation and reboot the phone starts with the Huawei Logo and goes black and starts to the Huawei logo and goes black and so on...
Here is a picture of where i am stuck at 90% right now, so close...:
hxxp://s13.postimg.org/p093toz5z/IMG_0192.jpg
SOLVED
After a 36 hour marathon my mate 7 is back and working. the trick was to flash the stock recovery for all Lollipop versions wich can be foudn here: http://forum.xda-developers.com/mat...8-7-0-mate7-android-5-1-t3156779/post61958212 via linux. I somehow seem to have had trouble over wndows.
And after that do the three button rescue with the newest B 324 firmware which I have had installed before I destroyed my OS..
and my camera is now running normaly which was the initial reason i tried to install a other firmare.
:laugh:
balpem said:
...the trick was to flash the stock recovery for all Lollipop versions
Click to expand...
Click to collapse
When you say flash stock recovery for all LP versions, did you flash and then reboot each time? or flash over and when complete, flash over again still on fastboot?
Can you briefly describe in steps? Tnx! and Glad you were able to recover
jfer671 said:
When you say flash stock recovery for all LP versions, did you flash and then reboot each time? or flash over and when complete, flash over again still on fastboot?
Can you briefly describe in steps? Tnx! and Glad you were able to recover
Click to expand...
Click to collapse
I flashed via fastboot the stock recovery which you can download via the link above. the provider (user rowihel2012) claims, that this recovery works for all lolipop stock roms.
After that I made a reboot and pressed (power button and volume+) to check if its installed.
Than I downloaded the lollipop version I have had previously installed. In my case this was the B324 European version.
I put it on my sd card (dload/UPDATE.app) and launched the phone with the three button rescue method. The recovery recognized the rom on the sdcard and started to flash the OS.
After less than 5 min, my phone was restored.
I have made the experience, when using certain roms (B324, B308 etc..) with certain stock recoveries, I was not able to flash the OS and the recovery stoped always at 90%.
The recovery linked above seems to work great for the B324 version, I haven't tried any other stock roms with it.
I wonder if this will work for B327? Seems the actual last update for LP was B324, now I can't seem to get out of this firmware to go back to KK. When I flash transition B300, it's successful...but for some odd reason, when I flash 137, 143, 145 or 148...I auto go back to B327. This, after the fact I'm flashing those firmware's recoveries. Any ideas what I might do to get out of 327?
---------- Post added at 01:42 PM ---------- Previous post was at 01:38 PM ----------
Also, what's this Vol+ and Power technique?, all I get is the three menu screen (reboot, factory reset and format cache).
jfer671 said:
I wonder if this will work for B327? Seems the actual last update for LP was B324, now I can't seem to get out of this firmware to go back to KK. When I flash transition B300, it's successful...but for some odd reason, when I flash 137, 143, 145 or 148...I auto go back to B327. This, after the fact I'm flashing those firmware's recoveries. Any ideas what I might do to get out of 327?
---------- Post added at 01:42 PM ---------- Previous post was at 01:38 PM ----------
Also, what's this Vol+ and Power technique?, all I get is the three menu screen (reboot, factory reset and format cache).
Click to expand...
Click to collapse
You can try this recovery above which should work for all lollipop roms but I have no better idea as I have had basicly the same problem and could only flash the former rom i had installed whch was B324.
The Vol+ and Power i do to get into the recovery menu (the three menu screen) to check if the recovery was flashed successfully. I have had often the problem after flashing a recovery that it did not work. this is to check if the recovery works.
When i tried to flash a cwm recovery, i couldnt enter any recovery mode after that anymore. I panicked at this point but than i realised that not all recoveries did work for me. For example I could never flash a CWM recovery, not sure why. Maybe because I tried to flash a 4.4 recovery and I had a 5.1 BOOT.img installed?
balpem said:
After a 36 hour marathon my mate 7 is back and working. the trick was to flash the stock recovery for all Lollipop versions wich can be foudn here: http://forum.xda-developers.com/mat...8-7-0-mate7-android-5-1-t3156779/post61958212 via linux. I somehow seem to have had trouble over wndows.
And after that do the three button rescue with the newest B 324 firmware which I have had installed before I destroyed my OS..
and my camera is now running normaly which was the initial reason i tried to install a other firmare.
:laugh:
Click to expand...
Click to collapse
balpem said:
You can try this recovery above which should work for all lollipop roms but I have no better idea as I have had basicly the same problem and could only flash the former rom i had installed whch was B324.
The Vol+ and Power i do to get into the recovery menu (the three menu screen) to check if the recovery was flashed successfully. I have had often the problem after flashing a recovery that it did not work. this is to check if the recovery works.
When i tried to flash a cwm recovery, i couldnt enter any recovery mode after that anymore. I panicked at this point but than i realised that not all recoveries did work for me. For example I could never flash a CWM recovery, not sure why. Maybe because I tried to flash a 4.4 recovery and I had a 5.1 BOOT.img installed?
Click to expand...
Click to collapse
I see, so then it seems like some recoveries did in fact work with fastboot on me, because the Vol+ and Power worked, but it either only put me in V100R001C900B300 OR MT7-L09C900B300. I've read that I can't just flash KK over LP, that I needed to flash the B300 which is why I flashed transition package first. Should I not have done this?
Once in transition mode though (I booted up and checked, then went back into recovery), if I flashed 4.4 (recovery), it oddly put me back to B327...strange even though the recovery flashed was B137 or B145.
Let me see this link above. I'm back again at 5.1.1 LP B327. I'll do instead fastboot and flash above the recovery and so on, and I'll post the results, if any. Oddly enough, if I flashed boot, recovery and system images of 4.4, I get an "Android" boot screen that hangs, no Huawei.
I really like LP because of some of the features not found in KK like the dual windows, camera tweaks, etc. But no root yet available. TWRP doesn't seem to work as well, fails in fastboot.
balpem said:
After a 36 hour marathon my mate 7 is back and working. the trick was to flash the stock recovery for all Lollipop versions wich can be foudn here: http://forum.xda-developers.com/mat...8-7-0-mate7-android-5-1-t3156779/post61958212 via linux. I somehow seem to have had trouble over wndows.
And after that do the three button rescue with the newest B 324 firmware which I have had installed before I destroyed my OS..
and my camera is now running normaly which was the initial reason i tried to install a other firmare.
:laugh:
Click to expand...
Click to collapse
Okay...so I was able to flash down to B324, but not via the link provided. What I did was, flash B300 cust.img on (fastboot) then flash boot/recovery/cust/system.img (fastboot). Rebooted with VolumeUp + Power to check for recovery (success), performed a wipe and done! Back to B324.
Now I gotta figure how to go back down to B145, which is where I was at with Root and with no problems at all. If I flash B300 again and then B145...I get the "Android" logo (instead of Huawei) and then the HAM7 reboots and recovers itself back to B324.
edit: If you are just looking for the solution, plz click here: http://forum.xda-developers.com/showpost.php?p=68626049&postcount=11
Hey there,
first of all I want to say Thank You for this great community and the work at XDA. Awesome. :good:
I bricked my Honor 6 H60-L02 and I am lost to bring it back to life. :crying:
Where it started:
I was using the official ROM from this thread [OFFICIAL] Honor 6 (L02, L12, L04) Stock ROMs. To be more specific it was the latest Android 6.0 EMUI 4.0 B823 that I installed with all the different OTA-Files starting with the original 5.1 ROM B535. The Honor was rooted and also the bootloader is still unlocked (I already checked the status via Fastboot.).
After I while the Honor 6 started to crash sometimes and the headphone-buttons didn't worked anymore. Then a few days ago the phone crashed and I was not able to boot it again.
And so I tried this:
Using the Rollback-Zip to go back to 5.1. But the 3btn-method didn't worked. The phone didn't want to boot into the recovery. Also the Vol+ and Power-Button didn't work to start the Recovery of the phone. Result: Bootloop.
So I installed ADB and Fastboot (with all necessary drivers) and tried to flash the phone with the 5.1 B535 (as mentioned in Honor 6 H60-L02 Hard Bricked - Only access to fastboot (Vol+ and Usb PC)) because there isn't a 6.0 B823 ROM available. I was able to flash boot, recovery, cust, system, userdata and another one I forgot right now. But the result was the same: Bootloop and no 3-btn or recovery via Vol+ and Power-Button. I also tried to flash it with the HonorTool. Same result.
Then I tried to flash different TWRP versions as recovery. Result: The same as above.
So I tried another official ROM 5.1 B526 because someone had the same problem and was able to recover his phone with this ROM (another thread in the forum). But that didn't worked ether.
Then I tried to flash all the img-files of the 5.1. B535 as crc, ptable and so on because I thought that there could be the problem. But when I tried e.g. to flash crc I get the error FAILED: command not allowed. So I tried to unlock the phones partition via Fastboot and fastboot flashine unlock_critical. But using the command unlock_critical gives me also the Failed error. So I was lost again.
Status right now:
I'm still able to boot into the bootloader via Vol- and Power. But right now the phone was running out of battery. Means I see the red battery symbol when I try to start the phone via the power button (without connecting to the PC or charger) but it isn't booting even into the bootloop. The red battery symbol pops up for a second and the screen went black again.
When I use the charger then the symbol changes to a green battery and stays there, but not the moving one that indicates that the phone is charging. When I use the Power button with usb-charger connected to start the phone I'm trapped in the bootloop again.
You see I already tried a lot of different things I could find on the forum. But nothing worked for me.
I know that it was a fault to try to install 5.1 B535 without the rollback, but I wasn't able to rollback as mentioned under point 1.
Maybe anyone could give me a hint and help me to bring my phone back to life.
Thx a lot! I appreciate that al lot!
If you need anymore informations, plz let me know.
Greets, mike175de
P.S: Sorry for my school english. It is a little bit rusty ;o)
mike175de said:
Hey there,
first of all I want to say Thank You for this great community and the work at XDA. Awesome. :good:
I bricked my Honor 6 H60-L02 and I am lost to bring it back to life. :crying:
Where it started:
I was using the official ROM from this thread [OFFICIAL] Honor 6 (L02, L12, L04) Stock ROMs. To be more specific it was the latest Android 6.0 EMUI 4.0 B823 that I installed with all the different OTA-Files starting with the original 5.1 ROM B535. The Honor was rooted and also the bootloader is still unlocked (I already checked the status via Fastboot.).
After I while the Honor 6 started to crash sometimes and the headphone-buttons didn't worked anymore. Then a few days ago the phone crashed and I was not able to boot it again.
And so I tried this:
Using the Rollback-Zip to go back to 5.1. But the 3btn-method didn't worked. The phone didn't want to boot into the recovery. Also the Vol+ and Power-Button didn't work to start the Recovery of the phone. Result: Bootloop.
So I installed ADB and Fastboot (with all necessary drivers) and tried to flash the phone with the 5.1 B535 (as mentioned in Honor 6 H60-L02 Hard Bricked - Only access to fastboot (Vol+ and Usb PC)) because there isn't a 6.0 B823 ROM available. I was able to flash boot, recovery, cust, system, userdata and another one I forgot right now. But the result was the same: Bootloop and no 3-btn or recovery via Vol+ and Power-Button. I also tried to flash it with the HonorTool. Same result.
Then I tried to flash different TWRP versions as recovery. Result: The same as above.
So I tried another official ROM 5.1 B526 because someone had the same problem and was able to recover his phone with this ROM (another thread in the forum). But that didn't worked ether.
Then I tried to flash all the img-files of the 5.1. B535 as crc, ptable and so on because I thought that there could be the problem. But when I tried e.g. to flash crc I get the error FAILED: command not allowed. So I tried to unlock the phones partition via Fastboot and fastboot flashine unlock_critical. But using the command unlock_critical gives me also the Failed error. So I was lost again.
Status right now:
I'm still able to boot into the bootloader via Vol- and Power. But right now the phone was running out of battery. Means I see the red battery symbol when I try to start the phone via the power button (without connecting to the PC or charger) but it isn't booting even into the bootloop. The red battery symbol pops up for a second and the screen went black again.
When I use the charger then the symbol changes to a green battery and stays there, but not the moving one that indicates that the phone is charging. When I use the Power button with usb-charger connected to start the phone I'm trapped in the bootloop again.
You see I already tried a lot of different things I could find on the forum. But nothing worked for me.
I know that it was a fault to try to install 5.1 B535 without the rollback, but I wasn't able to rollback as mentioned under point 1.
Maybe anyone could give me a hint and help me to bring my phone back to life.
Thx a lot! I appreciate that al lot!
If you need anymore informations, plz let me know.
Greets, mike175de
P.S: Sorry for my school english. It is a little bit rusty ;o)
Click to expand...
Click to collapse
Just flash boot, Cust, recovery and system images and let it boot normally. Don't do any button combo. I have had instances where it works. Give it a try.
With which version?
muradulislam said:
Just flash boot, Cust, recovery and system images and let it boot normally. Don't do any button combo. I have had instances where it works. Give it a try.
Click to expand...
Click to collapse
Thx for your reply.
With which version should I flash? B535 or B526? Should I only flash the three images boot, cust and system? Nothing else?
Thx for a reply!
mike175de said:
Thx for your reply.
With which version should I flash? B535 or B526? Should I only flash the three images boot, cust and system? Nothing else?
Thx for a reply!
Click to expand...
Click to collapse
You can use any firmware but the latest one should be better, and flash four images, boot, Cust, system and boot and let it boot normally.
Then put the dload folder with update.app in sd card and do an update from settings.
Thx. I will give it a try when I'm back from work.
I let you know if it is working.
mike175de said:
Thx. I will give it a try when I'm back from work.
I let you know if it is working.
Click to expand...
Click to collapse
I meant to say flash boot, Cust, recovery and system images.
Wrote boot twice
Nothing changed
Hey muradulislam,
Thx again.
I flashed the images (boot.img twice) but without success. Still the same error (with normal booting aka without any special button combination or with button combination). The honor boots and stays in the bootmode aka bootloop with the led blinkin red. And I still can't boot into recovery via Vol+ and Power..
Any other suggestions?
mike
mike175de said:
Hey muradulislam,
Thx again.
I flashed the images (boot.img twice) but without success. Still the same error (with normal booting aka without any special button combination or with button combination). The honor boots and stays in the bootmode aka bootloop with the led blinkin red. And I still can't boot into recovery via Vol+ and Power..
Any other suggestions?
mike
Click to expand...
Click to collapse
Of all the things you have already tried, the only thing remains to take it to a Huawei service center.
May be someone else can help you here but I have read most of honor 6 and 7 posts and I don't think there is anything there for this problem atm.
Hmm, thx. That is bad...
I bought this phone in China when I was there for work. And I suppose that the german service of Huwaei will not help me at all with this phone.
Does anybody else have any clue how to bring the phone back to life?
Thx a lot.
mike175de said:
Hmm, thx. That is bad...
I bought this phone in China when I was there for work. And I suppose that the german service of Huwaei will not help me at all with this phone.
Does anybody else have any clue how to bring the phone back to life?
Thx a lot.
Click to expand...
Click to collapse
I myself have an H60-L01, bought it from china, bricked and tried everything to revive it but could not, still have to try Huawei customer service in Pakistan, am not sure whether they will be able to help me or not, but will give it a try. I wish you luck buddy. Hope you find a solution.
It's alive ;o)
The phone is working again.
Here are the steps I did for everybody else confrontated with same problem:
1. Download your last working ROM or OTA-File: In my case the OTA-File OTA-EMUI 4.0_H60-L02-L12_B811_B823.zip from this Mega-Link:
https://mega.nz/#F!ztYliaxL!4gfyXozSW51eNahGZBDgBQ!KwhlRKYR
2. Unzip the file and extract recovery.img and boot.img with the Huawei Update Extractor (http://forum.xda-developers.com/showthread.php?t=2433454).
3. Boot the phone into fastboot mode (connect the USB cable, press the power button to turn off and immediately press the volume down button).
4. Use fastboot to flash the two images of 2. If you need fatsboot you can find it here http://www.mediafire.com/download/o5ruw752ked884u/adb+H60.zip (Extract adb.zip and copy the extracted files from 2. in the folder adb. In the adb folder run cmd.exe as administrator.)
5. Use this commands for flashing:
fastboot devices => If the device is recognized correctly it is displaying a series of numbers
fastboot flash recovery RECOVERY.img
fastboot flash boot BOOT.img
fastboot reboot
6. Charge the phone with the Huawei charger, not via USB/PC! (50% is enough.)
7. Download in the meantime the Developer ROM H60_EMUI3.1_Android5.1_6.1.1.zip from here:
https://mega.nz/#F!ztYliaxL!4gfyXozSW51eNahGZBDgBQ!6w5inQ6Z
8. Extract the zip file from 7. and copy UPDATE.app onto your SD-Card into /dload
9. Insert the SD without connecting.
9.1. Disconnect the USB cable from your PC or charger.
9.2. Press the Power button to turn off (maybe that is not necessary.)
9.3. When you feel the vibration press 3btn (Vol+ and Vol- and Power).
9.4. When the Honor logo appears connect your SD-Card (continue to press 3btn for 8 -10 more seconds) => Wait for the recovery process, it should start automatically.
10. After installation Android boots. Skip the first step installation (you should now have the 6.1.1. Developer-Edition installed). Rollback to Android 5.1.1 with the Rollback-File Rollback 591 EMUI3.0.zip from here:
http://www.mediafire.com/download/9qrd8zm9280gy5e/Rollback+591+EMUI3.0.zip
Do do so put the unzipped UPDATE.app from the Rollback-File onto your SD-Card and do a local update via the Update Manager.
11. Boot into Android again (it will still be the 6.1.1 Developer Edition). In my case I want to install the latest Android 5.1.1 B535 from here:
https://mega.nz/#F!ztYliaxL!4gfyXozSW51eNahGZBDgBQ!6w5inQ6Z
I did it via local update again.
12.. After installation and booting => Voila here is your working Android 5.1.1 B535 again. Have fun
13. Brick it again with updating to Android 6.0
I hope I could help somebody with my experience to bring his/her phone back to life.
CU, mike
The same can not restore brick
Hello! In what condition I have a phone? My phone is loaded in error func_boot_kernel.
igorxxl said:
Hello! In what condition I have a phone? My phone is loaded in error func_boot_kernel.
Click to expand...
Click to collapse
Have you unlocked and rooted it?
When does it says that message?
error! no func. func_boot_kernel or _recovery
zinko_pt said:
Have you unlocked and rooted it?
When does it says that message?
Click to expand...
Click to collapse
The bootloader is unlocked. Root is. Phone is loaded into the error! no func. func_boot_kernel. If you try to enter into the recovery, the error! no func. func_boot_recovery.
The error is the same as here club.huawei.com/thread-7962289-1-1.html
I tried to put EMUI4.0, then the phone stopped working. Through ADB stitched, weighting system, boot, recovery, cust.img. It shows all ok. But then the error again. He tried to put different versions of TWRP. On the 3 button also does not work.
Thank you for your attention to my problem.
igorxxl said:
The bootloader is unlocked. Root is. Phone is loaded into the error! no func. func_boot_kernel. If you try to enter into the recovery, the error! no func. func_boot_recovery.
The error is the same as here club.huawei.com/thread-7962289-1-1.html
I tried to put EMUI4.0, then the phone stopped working. Through ADB stitched, weighting system, boot, recovery, cust.img. It shows all ok. But then the error again. He tried to put different versions of TWRP. On the 3 button also does not work.
Thank you for your attention to my problem.
Click to expand...
Click to collapse
You can't use 3 button with custom recovery and root. It wont work.
You need stock recovery in the same version as the rest of files used to flash other partitions.
Flash all stock partitions, then just boot the phone. Check if it works. Forget about TWRP and root for now. One thing at a time.
Nothing helps. I sew different versions via Fastboot. Everywhere all shows OK. However, when you restart the exact same mistake again ..
igorxxl said:
Nothing helps. I sew different versions via Fastboot. Everywhere all shows OK. However, when you restart the exact same mistake again ..
Click to expand...
Click to collapse
You can also try installing custom recovery and restore a twrp backup of ROM.
zinko_pt said:
You can't use 3 button with custom recovery and root. It wont work.
You need stock recovery in the same version as the rest of files used to flash other partitions.
Flash all stock partitions, then just boot the phone. Check if it works. Forget about TWRP and root for now. One thing at a time.
Click to expand...
Click to collapse
goldfinv said:
You can also try installing custom recovery and restore a twrp backup of ROM.
Click to expand...
Click to collapse
i'm in the same situation with my honor 6 plus pe-ul00 i'll try this metod!
mike175de said:
The phone is working again.
Here are the steps I did for everybody else confrontated with same problem:
1. Download your last working ROM or OTA-File: In my case the OTA-File OTA-EMUI 4.0_H60-L02-L12_B811_B823.zip from this Mega-Link:
https://mega.nz/#F!ztYliaxL!4gfyXozSW51eNahGZBDgBQ!KwhlRKYR
2. Unzip the file and extract recovery.img and boot.img with the Huawei Update Extractor (http://forum.xda-developers.com/showthread.php?t=2433454).
3. Boot the phone into fastboot mode (connect the USB cable, press the power button to turn off and immediately press the volume down button).
4. Use fastboot to flash the two images of 2. If you need fatsboot you can find it here http://www.mediafire.com/download/o5ruw752ked884u/adb+H60.zip (Extract adb.zip and copy the extracted files from 2. in the folder adb. In the adb folder run cmd.exe as administrator.)
5. Use this commands for flashing:
fastboot devices => If the device is recognized correctly it is displaying a series of numbers
fastboot flash recovery RECOVERY.img
fastboot flash boot BOOT.img
fastboot reboot
6. Charge the phone with the Huawei charger, not via USB/PC! (50% is enough.)
7. Download in the meantime the Developer ROM H60_EMUI3.1_Android5.1_6.1.1.zip from here:
https://mega.nz/#F!ztYliaxL!4gfyXozSW51eNahGZBDgBQ!6w5inQ6Z
8. Extract the zip file from 7. and copy UPDATE.app onto your SD-Card into /dload
9. Insert the SD without connecting.
9.1. Disconnect the USB cable from your PC or charger.
9.2. Press the Power button to turn off (maybe that is not necessary.)
9.3. When you feel the vibration press 3btn (Vol+ and Vol- and Power).
9.4. When the Honor logo appears connect your SD-Card (continue to press 3btn for 8 -10 more seconds) => Wait for the recovery process, it should start automatically.
10. After installation Android boots. Skip the first step installation (you should now have the 6.1.1. Developer-Edition installed). Rollback to Android 5.1.1 with the Rollback-File Rollback 591 EMUI3.0.zip from here:
http://www.mediafire.com/download/9qrd8zm9280gy5e/Rollback+591+EMUI3.0.zip
Do do so put the unzipped UPDATE.app from the Rollback-File onto your SD-Card and do a local update via the Update Manager.
11. Boot into Android again (it will still be the 6.1.1 Developer Edition). In my case I want to install the latest Android 5.1.1 B535 from here:
https://mega.nz/#F!ztYliaxL!4gfyXozSW51eNahGZBDgBQ!6w5inQ6Z
I did it via local update again.
12.. After installation and booting => Voila here is your working Android 5.1.1 B535 again. Have fun
13. Brick it again with updating to Android 6.0 [emoji14]
I hope I could help somebody with my experience to bring his/her phone back to life.
CU, mike
Click to expand...
Click to collapse
I got a problem at 9.3 or 9.4. The recovery wont start i see only honor logo i used PE_EMUI3.1_Android5.1_6.1.1.zip (as developer edition i.e sdcard/dload/UPDATE.APP) and PE-UL00-V100R001CHNC00B200.zip to extract and flash BOOT.img and RECOVERY.img
any ideas why i can't enter in recovery? =(
EDIT: "fixed with DC-Phoenix tool"
Hi, need some urgent help here.
I was trying to install a custom rom, so I unlocked first the bootloader, then flashed twrp 3.0.2 for Android 5.1 and with it I flashed KangVip rom (porto from honor 6).
Problem was it didn't boot, just black screen.
So I supposed the problem was with the rom so I flashed via fastboot the aosp 6, obviously with same results.
I tried lot of stuff (twrp 2.8.x.x, reinstall stock firmware, restore twrp backup of stock full firmware and so on - I did almost everything I could do) and now I'm with a Huge problem: no huawei logo at start, just a white screen and nothing happen. I have twrp 3.0.2 for 5.1 installed right now but I can't install stock recovery.
Please help me, what do I gotta do?
[emoji30]
the ported rom is based on Android 6.0 you have Android 5.1 youk should flash 5.1 based rom..
it's good to flash stock and update official to b560 or b571 depending on which region to have then flash twrp recovery and then flash desire rom..
fazi2015 said:
the ported rom is based on Android 6.0 you have Android 5.1 youk should flash 5.1 based rom..
it's good to flash stock and update official to b560 or b571 depending on which region to have then flash twrp recovery and then flash desire rom..
Click to expand...
Click to collapse
Thx for this.
But I have a problem, I can't install stock recovery and if I try to flash the .img files extracted from update.app nothing happens.
Also, I still have that problem with huawei logo disappeared and a blank white screen instead.
Sent from my HUAWEI GRA-L09 using Tapatalk
boot into bootloader and flash stock recovery but if you know what exactly firmware was you have(bxxx) then no need to flash recovery just put update.app to your sd card and then force update three buttons combination (volume both and power) turn off it remove data cable then press these three buttons it'll go in recovery sometime but try two or three times(in recovery turn off device) and try again if that method not work you should flash stock recovery to do so and if it didn't go to bootloader(fastboot) then connect data cable and then press vol- and power it'll go to bootloader in bootloader flash stock recovery then force update your device....
fazi2015 said:
boot into bootloader and flash stock recovery but if you know what exactly firmware was you have(bxxx) then no need to flash recovery just put update.app to your sd card and then force update three buttons combination (volume both and power) turn off it remove data cable then press these three buttons it'll go in recovery sometime but try two or three times(in recovery turn off device) and try again if that method not work you should flash stock recovery to do so and if it didn't go to bootloader(fastboot) then connect data cable and then press vol- and power it'll go to bootloader in bootloader flash stock recovery then force update your device....
Click to expand...
Click to collapse
Solved, thanks!
Sent from my HUAWEI GRA-L09 using Tapatalk
fazi2015 said:
boot into bootloader and flash stock recovery but if you know what exactly firmware was you have(bxxx) then no need to flash recovery just put update.app to your sd card and then force update three buttons combination (volume both and power) turn off it remove data cable then press these three buttons it'll go in recovery sometime but try two or three times(in recovery turn off device) and try again if that method not work you should flash stock recovery to do so and if it didn't go to bootloader(fastboot) then connect data cable and then press vol- and power it'll go to bootloader in bootloader flash stock recovery then force update your device....
Click to expand...
Click to collapse
Hope you can help me out here...I had just gotten my HAM7 for a couple of days. Was on 4.4.2 B120, was able to get it up to B326. Just yesterday I attempted to flash up to B331 and it succeeded according to the "local update" option. Then it went on boot loop. I tried doing the force 3-button option and that worked to the point of saying it succeeded and will reboot. Now I'm stuck on Ascend Mate logo. I can no longer get into factory option mode (V+Power), only fastboot mode. Also, I can't do force update no more so I can't try any other "update.app" unless I'm missing something here.
Any help in getting this unit at least back to working condition will be a BIG help. I just received this two days ago.
Thx!!!!
jfer671 said:
Hope you can help me out here...I had just gotten my HAM7 for a couple of days. Was on 4.4.2 B120, was able to get it up to B326. Just yesterday I attempted to flash up to B331 and it succeeded according to the "local update" option. Then it went on boot loop. I tried doing the force 3-button option and that worked to the point of saying it succeeded and will reboot. Now I'm stuck on Ascend Mate logo. I can no longer get into factory option mode (V+Power), only fastboot mode. Also, I can't do force update no more so I can't try any other "update.app" unless I'm missing something here.
Any help in getting this unit at least back to working condition will be a BIG help. I just received this two days ago.
Thx!!!!
Click to expand...
Click to collapse
are you have unlock bootloader or not..
fazi2015 said:
are you have unlock bootloader or not..
Click to expand...
Click to collapse
Yes, bootloader is unlocked. FYI, I can't do Vol+ Power or 3-button force. I have no idea what went wrong after the B331 update.app flash. It said successful then boot loop after. I have looked all over the forums and tried everything from flashing C900B300 rollback to try and get 4.4.2 that I started out with, but I really don't know which firmware to start with. The last update.app files I was using was the European variants. Phone was originally locked to Ecuador MoviStar network at B120SP04, then I flashed up to B324 5.1.1. Rooted and then wanted to upgrade to B331 so I unrooted and flashed. Now I'm stuck.
jfer671 said:
Yes, bootloader is unlocked. FYI, I can't do Vol+ Power or 3-button force. I have no idea what went wrong after the B331 update.app flash. It said successful then boot loop after. I have looked all over the forums and tried everything from flashing C900B300 rollback to try and get 4.4.2 that I started out with, but I really don't know which firmware to start with. The last update.app files I was using was the European variants. Phone was originally locked to Ecuador MoviStar network at B120SP04, then I flashed up to B324 5.1.1. Rooted and then wanted to upgrade to B331 so I unrooted and flashed. Now I'm stuck.
Click to expand...
Click to collapse
now you should flash twrp recovery in fastboot mode and then flash a custom rom like kangvip I'll send you link soon...
fazi2015 said:
now you should flash twrp recovery in fastboot mode and then flash a custom rom like kangvip I'll send you link soon...
Click to expand...
Click to collapse
Thank you very much....hope that will solve the boot issue and bring this unit back to life
Alright, so I've given up complete hope that I can get my unit back up and running again. I've tried so many ways already with no success (fastboot/adb, force upgrade, etc.,), and even tried to copy my second HAM7 images (via sdk tools) and to no avail.
The thing I'm trying to understand is where exactly do I start with trying to revive? When I first got this device from eBay, it was apparently still on "MoviStar" Telefonica-Spain network so my network bars showed "R" for roaming. Somehow, I was able to flash it from being on V100R001C00B120SP04a and upgrade to B127>B145>B324 which made me able to use my own service normally. It worked fine and I was even able to root it. Decided to do a last upgrade to B331 and while the local update option showed it as successfully installed, it went into boot loop ever since. Hence, I used European firmwares for most of the flashing. My second mate was on B145 and I was able to get that to B331, which is running fine right now.
ATM, I am ONLY able to do Volume-/Power to get into fastboot.
Doesn't work:
- V+/Power (stock recovery)
- V-+/Power (3-button force)
What works:
- V-/Power with USB for fastboot
*Bootloader is unlocked, but I do believe that after flashing the last firmware of B331, I may have done a factory wipe, which probably reset the USB debugging option as well. So, I'm sure I'm stuck with a device that just might be flashed on the wrong firmware and is factory reset which prevents me from flashing a custom rom or even the stock rom???
Any last advice I would be so thankful for...still waiting on the link for KangVip rom from (fazi2015)
All the best...
jfer671 said:
Alright, so I've given up complete hope that I can get my unit back up and running again. I've tried so many ways already with no success (fastboot/adb, force upgrade, etc.,), and even tried to copy my second HAM7 images (via sdk tools) and to no avail.
The thing I'm trying to understand is where exactly do I start with trying to revive? When I first got this device from eBay, it was apparently still on "MoviStar" Telefonica-Spain network so my network bars showed "R" for roaming. Somehow, I was able to flash it from being on V100R001C00B120SP04a and upgrade to B127>B145>B324 which made me able to use my own service normally. It worked fine and I was even able to root it. Decided to do a last upgrade to B331 and while the local update option showed it as successfully installed, it went into boot loop ever since. Hence, I used European firmwares for most of the flashing. My second mate was on B145 and I was able to get that to B331, which is running fine right now.
ATM, I am ONLY able to do Volume-/Power to get into fastboot.
Doesn't work:
- V+/Power (stock recovery)
- V-+/Power (3-button force)
What works:
- V-/Power with USB for fastboot
*Bootloader is unlocked, but I do believe that after flashing the last firmware of B331, I may have done a factory wipe, which probably reset the USB debugging option as well. So, I'm sure I'm stuck with a device that just might be flashed on the wrong firmware and is factory reset which prevents me from flashing a custom rom or even the stock rom???
Any last advice I would be so thankful for...still waiting on the link for KangVip rom from (fazi2015)
All the best...
Click to expand...
Click to collapse
https://mega.co.nz/#!3N4RzbJY!saB4NY...Ao5goVNiSXAjEc
I am not 100% sure about this rom but you can try it in fastboot you should flash twrp recovery first..
fazi2015 said:
https://mega.co.nz/#!3N4RzbJY!saB4NY...Ao5goVNiSXAjEc
I am not 100% sure about this rom but you can try it in fastboot you should flash twrp recovery first..
Click to expand...
Click to collapse
Unfortunately, it says the file is no longer available
jfer671 said:
Unfortunately, it says the file is no longer available
Click to expand...
Click to collapse
try this all information is here
https://forum.xda-developers.com/mate-7/orig-development/rom-kangvip-rom-mate7-emui3-1-b351-t3228597
fazi2015 said:
try this all information is here
https://forum.xda-developers.com/mate-7/orig-development/rom-kangvip-rom-mate7-emui3-1-b351-t3228597
Click to expand...
Click to collapse
Okay, so final result is I'm stuck on a frozen logo now. The twrp bat file again showed success in flashing and rebooted the device, but I'm hung on the "Huawei Ascend" logo. I have to pull the battery to shut it off, otherwise it stays on. So I'm now sure that it's a hard bricked device since I did the stupid thing of factory resetting which probably reset the usb debug...making it almost impossible to flash any firmware now.
Thanks for the help anyways...I really appreciate it. Gonna throw this up on eBay and see if anyone wants it for parts
jfer671 said:
Okay, so final result is I'm stuck on a frozen logo now. The twrp bat file again showed success in flashing and rebooted the device, but I'm hung on the "Huawei Ascend" logo. I have to pull the battery to shut it off, otherwise it stays on. So I'm now sure that it's a hard bricked device since I did the stupid thing of factory resetting which probably reset the usb debug...making it almost impossible to flash any firmware now.
Thanks for the help anyways...I really appreciate it. Gonna throw this up on eBay and see if anyone wants it for parts
Click to expand...
Click to collapse
I know it's annoying but last time I research more and guide you I was have same problem don't give up....
I send you recovery flash in fastboot no need of usb debugging usb debugging need for adb not for fastboot in fastboot flash recovery by your self download it
https://mega.co.nz/#!GRw0CZjQ!iZllDkA6yJeWk7iEA4vEVA94r2nM_YjAuiS8B9IZdm0
then extract the zip go to resource and hold shift and left click then select open command port here then power off device completely boot into fastboot (bootloader) connect the device to pc and in command port type
fastboot flash recovery twrp_2_7.img
after that type
fastboot reboot and hold the volume- button of device it'll boot into recovery if you success then reply..
I've noticed two things when flashing KK or LP. On KK, the phone does a constant boot loop with Huawei logo (on off on off), but on LP the Huawei logo hangs...it doesn't boot loop. Is this an indication or just a fault with both OS?