Tested with Micromax Unite 2
Procedure (SP Flash tools) :
1. Make a backup using read back. Guide->here
2. Make a backup using ctr recovery. CTR recovery->here
3. Make a backup of NVRAM data. Guide->here
3.a. Data 2gb, internal sd 340mb. (kitkat)
Extract ebr1, ebr2 from this zip.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
3.b. Data 2.1gb, internal sd 340mb (this one should work when flashed using ctr recovery) (kitkat)
MMX Data Repartition 2.1gb+340mb
3.c. Data 2.2gb, internal sd 28mb (tested in jelly bean rom, someone test in kitkat)
EBR1 and EBR2
4. Load scatter file you used to flash ctr recovery.
5. Select ebr1 and ebr2 in sp flash tools.
6. Click download and connect your phone in switched off state (without battery preferred).
7. Once done, remove the phone and reboot to recovery by pressing both volume buttons and power on.
8. Format format data cache and system.
9. Restore your ctr backup.
10. Reboot.
If after reboot u get a notification of damaged sd card, tap it and format it.
If you get no imei/baseband, restore your NVRAM data.
Procedure 2(CWM NOT TESTED) :
1. Make read back backup and ctr backup.
2. Flash this zip in recovery.
3. Restore your ctr backup.
4. Reboot.
Press thanx if this worked for you.
Nice thing bro!
2.2gb is not working (4.4.2)
1. the int. sd card doesn't format and stops detecting sims after a while(i thought a reboot might get it working and then..)
2. it doesn't even shows the boot logo after the reboot
however 2gb is working fine...
kanodiatushar said:
2.2gb is not working (4.4.2)
1. the int. sd card doesn't format and stops detecting sims after a while(i thought a reboot might get it working and then..)
2. it doesn't even shows the boot logo after the reboot
however 2gb is working fine...
Click to expand...
Click to collapse
Try flashing data partition using stock recovery. Restore nvram data for sim.
Guve it a shot.
i forgot to take backup using CTR recovery
Sudeep Duhoon said:
Tested with Micromax Unite 2
Procedure (SP Flash tools) :
1. Make a backup using read back. Guide->here
2. Make a backup using ctr recovery. CTR recovery->here
3. Make a backup of NVRAM data. Guide->here
3.a. Data 2gb, internal sd 340mb. (kitkat)
Extract ebr1, ebr2 from this zip.
3.b. Data 2.1gb, internal sd 340mb (this one should work when flashed using ctr recovery) (kitkat)
MMX Data Repartition 2.1gb+340mb
3.c. Data 2.2gb, internal sd 28mb (tested in jelly bean rom, someone test in kitkat)
EBR1 and EBR2
4. Load scatter file you used to flash ctr recovery.
5. Select ebr1 and ebr2 in sp flash tools.
6. Click download and connect your phone in switched off state (without battery preferred).
7. Once done, remove the phone and reboot to recovery by pressing both volume buttons and power on.
8. Format format data cache and system.
9. Restore your ctr backup.
10. Reboot.
If after reboot u get a notification of damaged sd card, tap it and format it.
If you get no imei/baseband, restore your NVRAM data.
Procedure 2(CWM NOT TESTED) :
1. Make read back backup and ctr backup.
2. Flash this zip in recovery.
3. Restore your ctr backup.
4. Reboot.
Press thanx if this worked for you.
Click to expand...
Click to collapse
I forgot to take backup using ctr recovery. Now mobile stuck at logo. How can i restore backup using read back
jankalai said:
I forgot to take backup using ctr recovery. Now mobile stuck at logo. How can i restore backup using read back
Click to expand...
Click to collapse
Look before asking. Try google ' How can i restore read back backup using sp flash tools'
Sudeep Duhoon said:
Look before asking. Try google ' How can i restore read back backup using sp flash tools'
Click to expand...
Click to collapse
I tried it showing result for iphone only..Please help me bro
jankalai said:
I tried it showing result for iphone only..Please help me bro
Click to expand...
Click to collapse
Don't lie.
Extending Internal memory using Link2SD
Bro,
is it possible to extend the default internal memory using Link2SD??
Installed recovery.img., then supersu., rooted successfully.
8 GB (class 4) SD card., partitioned as 4GB FAT32 and 4GB EXT4., Using Link2SD created a mount script successfully.
But., After linking apps (create "link" in link2sd) it ask's for a reboot., after reboot., apps disapper and unable to open.!!!
but can see /data/sdexta2/app.apk /data/sdexta2/app-lib/app's-lib and /data/sdexta2/dev-cache/apps'cache
but unable to open app!! tried so many times.... please any one can help me???????
not having ctr back up
now my phone is stuck with the logo while rebooting. please help me out to reboot my phone
rsenthilkumar said:
Bro,
is it possible to extend the default internal memory using Link2SD??
Installed recovery.img., then supersu., rooted successfully.
8 GB (class 4) SD card., partitioned as 4GB FAT32 and 4GB EXT4., Using Link2SD created a mount script successfully.
But., After linking apps (create "link" in link2sd) it ask's for a reboot., after reboot., apps disapper and unable to open.!!!
but can see /data/sdexta2/app.apk /data/sdexta2/app-lib/app's-lib and /data/sdexta2/dev-cache/apps'cache
but unable to open app!! tried so many times.... please any one can help me???????
Click to expand...
Click to collapse
Format ext-sd using recovery once.
I faced this issue when I partition and used link2sd right after that, but when I formatted ext sd from recovery, it worked fine.
Remove links of all apps, flash this in recovery, reboot, use link2sd.
kauthuk said:
now my phone is stuck with the logo while rebooting. please help me out to reboot my phone
Click to expand...
Click to collapse
Restore ur cwm backup.
Lost Backup
Sudeep Duhoon said:
Tested with Micromax Unite 2
Procedure (SP Flash tools) :
1. Make a backup using read back. Guide->here
2. Make a backup using ctr recovery. CTR recovery->here
3. Make a backup of NVRAM data. Guide->here
3.a. Data 2gb, internal sd 340mb. (kitkat)
Extract ebr1, ebr2 from this zip.
3.b. Data 2.1gb, internal sd 340mb (this one should work when flashed using ctr recovery) (kitkat)
MMX Data Repartition 2.1gb+340mb
3.c. Data 2.2gb, internal sd 28mb (tested in jelly bean rom, someone test in kitkat)
EBR1 and EBR2
4. Load scatter file you used to flash ctr recovery.
5. Select ebr1 and ebr2 in sp flash tools.
6. Click download and connect your phone in switched off state (without battery preferred).
7. Once done, remove the phone and reboot to recovery by pressing both volume buttons and power on.
8. Format format data cache and system.
9. Restore your ctr backup.
10. Reboot.
If after reboot u get a notification of damaged sd card, tap it and format it.
If you get no imei/baseband, restore your NVRAM data.
Procedure 2(CWM NOT TESTED) :
1. Make read back backup and ctr backup.
2. Flash this zip in recovery.
3. Restore your ctr backup.
4. Reboot.
Press thanx if this worked for you.
Click to expand...
Click to collapse
Sir i have taken the backup, and flashed the zip file... but while trying to restore the image in CTR ... i accidentally formatted my sd card which had all my backups....
im confused.... what should i do to get my phone back ???
can i take a backup from someother unite 2 and restore it in mine ??
but i dont know anyone using this phone...
please do help me...
im in a critical situation....
quries for the process
hii Sandeep this is my 1st time doing something out of ordinary i have some doubts in my mind about this partition process
1.Do i need to root 1st to apply the process
2.do i press the download button keeping the usb plugged in/not
3.how much space is alloted by this process should it cover 20apps with 50mb each at the same time
4.if in the future i decide to root it with cwm recovery do i get the same alloted space by this process or not
5.what is your opinion of this apps like link2sd,foldermount,internal to external sd can these be used for low internal storage and would these apps work on the device???
plz do reply as my decisions are based on your answer!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
I am having the 8gb model..
I don't think that this would work..
any other tutorial for 8gb model.. ?
Ha\/0c said:
I am having the 8gb model..
I don't think that this would work..
any other tutorial for 8gb model.. ?
Click to expand...
Click to collapse
Send me ebr1 and ebr2 files from your read back data. I will see what i can do.
Kiran Anto said:
Sir i have taken the backup, and flashed the zip file... but while trying to restore the image in CTR ... i accidentally formatted my sd card which had all my backups....
im confused.... what should i do to get my phone back ???
can i take a backup from someother unite 2 and restore it in mine ??
but i dont know anyone using this phone...
please do help me...
im in a critical situation....
Click to expand...
Click to collapse
Restore through sp flash tools.
Use the read back backup.
2.2gb may brick kitkat
Sudeep Duhoon said:
Tested with Micromax Unite 2
Procedure (SP Flash tools) :
1. Make a backup using read back. Guide->here
2. Make a backup using ctr recovery. CTR recovery->here
3. Make a backup of NVRAM data. Guide->here
3.a. Data 2gb, internal sd 340mb. (kitkat)
Extract ebr1, ebr2 from this zip.
3.b. Data 2.1gb, internal sd 340mb (this one should work when flashed using ctr recovery) (kitkat)
MMX Data Repartition 2.1gb+340mb
3.c. Data 2.2gb, internal sd 28mb (tested in jelly bean rom, someone test in kitkat)
EBR1 and EBR2
4. Load scatter file you used to flash ctr recovery.
5. Select ebr1 and ebr2 in sp flash tools.
6. Click download and connect your phone in switched off state (without battery preferred).
7. Once done, remove the phone and reboot to recovery by pressing both volume buttons and power on.
8. Format format data cache and system.
9. Restore your ctr backup.
10. Reboot.
If after reboot u get a notification of damaged sd card, tap it and format it.
If you get no imei/baseband, restore your NVRAM data.
Procedure 2(CWM NOT TESTED) :
1. Make read back backup and ctr backup.
2. Flash this zip in recovery.
3. Restore your ctr backup.
4. Reboot.
Press thanx if this worked for you.
Click to expand...
Click to collapse
2.2gb in kitkat doesnt work. The following happens if done so
1.Damaged sdcard notification appears
2. formating fails
3. no imei/baseband
4. if rebooted ,phone is bricked :crying:
5. recovery throws "E: Can't mount /cache/recovery/command " error
Flashed readback backup , ctr2.2, ctr backup ,nvram backup and mp phone is back
bro i tried using this method....tried using both recovery but it did not work had to restore my phone via sp flash tools....u said to restore the backup after but it says MD5 changed...???..i wanted to get 2 gb for my apps.......PLEZ HELP.....!!!!
Micromax Unite2 A106 8GB vs 4GB models
I am very new to mobile dev. stuff. I recently bought Micromax Unite2 A106 8GB model.
I have been searching internet for some information and there is none which clear enough for me to understand.
I have a few questions, if you can answer, i'll be glad.
1. Is the ROOTING process and software and files required for rooting Micromax Unite2 A106 8GB same as Micromax Unite2 A106 4GB?
2. Is REPARTITIONING process and software and files required for Micromax Unite2 A106 8GB same as Micromax Unite2 A106 4GB?
Here are EBR1 and EBR2 for 8GB model.
here are the EBR files for Unite 2 8GB model.
EBR files for Unite2 8GB
Sudeep Duhoon said:
Send me ebr1 and ebr2 files from your read back data. I will see what i can do.
Click to expand...
Click to collapse
Here are the EBR files and the scatter file from Micromax Unite 2 A106 8GB model.
Related
I have root access on my xolo q800 but no Rom is installed. How can I install a Rom and back up my current android please help me!!!!!!
digambar908 said:
I have root access on my xolo q800 but no Rom is installed. How can I install a Rom and back up my current android please help me!!!!!!
Click to expand...
Click to collapse
For backup:
Go to cwm
Select backup and restore
Select backup to internal/external as per ur requirement
Reboot
You are done:thumbup:
For flashing rom:
Put rom in ur internal sd card
Go to cwm
Select wipe data/factory reset
Select wipe cache partition
Go to advanced and select wipe delvic cache
Go back and select install zip from sd card
Select choose zip sd card
Then select chooze zip from internal sd card and select zip file
Reboot
Enjoy:thumbup:
HIT THANKS IF I HELPED YOU
Sent from my GT-S7500
Please Help me. Your Rom is beautifull!!!! I want it
Is only a update or full?
Give me, please, more Flash info .
I must first flash version 1.1 and then 2 or I can directly flash the version 2?
Detailed info I would like to install this room, I must first format the ROM I have on the phone now?
is automatically rewritten or everything?
Is that the way:
1) Download JMP™ ROM .zip File
2) Put into External/Internal SD Card
3) Go To CMW Recovery
4) Wipe Data/Factory Reset And Wipe Partition
5) From Advance Menu Do Dalvik Catch Clear
6) From Advance Menu Do Battery State Clear
7) Go in Mount And Storage select FORMAT SYSTEM
8) Select Install From SD and Select File And Click YES
9) Reboot Your System
10) Done ?
Thaaaaaaaaaaa.......nk's
u will be able to flash it directly....like jmp
BB2.0
this Rom is going to be full Rom can be flashed by Clockwork recovery
It's a full rom package
I am using stock job and rooted....
So can I flash directly v2???
Thanku...
Sent from my Micromax A110 using xda premium
Yes u can
Sent from my Micromax A110 using xda premium
Stock ROM V2 for Micromax A117 Canvas Magnus
How To Flash :
( You must take CMW Backup for Revert back to your old system )
1) Download ROM
2) Put into External/Internal SD Card
3) Go To CMW Recovery
4) Wipe Data/Factory Reset And Wipe Partition
5) From Advance Menu Do Dalvik Catch Clear
6) Go in Mount And Storage select FORMAT SYSTEM
7) Select Install From SDCard, Then Select File And Click YES
8) Reboot Your System
Click to expand...
Click to collapse
Download
Download ROM
Note :
I Will Not Be Responsible For Any Bricked Devices or Any Problem So Flash At Your Own Risk.
Press Thanks button if you like my work.
I open this thread because I never found any proper solution for mtk6575 repartition, it's little different from other mtk phones.you have to edit the mbr file for increasing internal storage and also the scatter file...here i share a zip file it's not my work....file is moded by jassonrr for micromax a90 I used it on my clone note2 mtk 6575 and it's working for me..it's for 4gb rom you get 1.97gb internal and 571mbu on SD card.
First of all do a cwm backup and also you need a working flash tool backup, make it sure this thing.
now select scatter file give in the zip using sp flash tool and try to flash only mbr ebr1 and ebr2.if it works for you than go to cwm recovery wipe data factory reset,restore your backup..wipe cache partition and dalvic cache.reboot your phone format SD card...you will see your internal storage increase in settings.
Now come to the tough part if above steps is not working for you.....at first open your scatter file and given scatter file match all the value except user data and fat partition,also in the given scatter file it's replace the android name with gionee so it's not a problem be sure just values are same.
If everything ok than replace the value of user data and fat partition from given scatter to your scatter file....now open sp flashtool format your phone except bootloader....now select the modified scatter file and flash the full rom with given mbr ebr1 ebr2....after complete the flash go to cwm recovery wipe data factory reset...restore your backup wipe cache partition and dalvic cache,reboot phone and format SD....you will find your new internal storage in settings....
Do it with your own risk.. I am not responsible if any thing happen to your phone.
Bugs: you cannot see your external SD from cwm recovery.
Please hit thanks if you find me helpful..
follow this
based on:
http://apkandroidgamehdzone.blogspot.sg/2012/07/romhaipai-noble-i9220-52-inch-mtk6575.html
make your own stable baseline, especially with cwm-based recovery
boot as per normal
copy MTK6575_2gb_for apps_512_internal memory.zip from to ext sdcard
Boot to recovery, which is cwm-ported if based on the baseline,
Prepare cwm backup in ext sdcard
install update from zip
MTK6575_2gb_for apps_512_internal memory.zip by those MTK gods - angelobiz
it basically have scripts that update the MBR (the key in MTK6575).
Usually other MTK devices need to modify EBR1 and 2
but this is not applicable for most MTK6575 models,
you will just hang at boot or dead if you try modifying EBRs
it ended perfectly by formating the usr_data and fat partition.
then restore your cwm backup
where it will fill up back your whatever baseline to the new space
boot as per normal
PROFIT!!!!
testing now
I have flashed a new rom on my phone with twrp 3.4.0.0
When I got to the new UI I had no free space (both internal and sdcard)
Back to twrp I took these steps:
1. Boot into TWRP recovery.
2. Select Wipe » Advanced Wipe.
3. Tick/check the Data partition.
4. Select Repair or Change File System button.
5. And lastly select Resize File System button.
that solved the internal storage size, but the storage of sdcard shows 80MB when it should read 128GB.
I tryed the same method for sdcard but it cant be done on sdcard selection.
Is there any solution without formating sdcard?
if not please provide a solution with formating on twrp.
I have searched for a solution but no result...
Please help! i have no time to search right now!
PanosT said:
I have flashed a new rom on my phone with twrp 3.4.0.0
When I got to the new UI I had no free space (both internal and sdcard)
Back to twrp I took these steps:
1. Boot into TWRP recovery.
2. Select Wipe » Advanced Wipe.
3. Tick/check the Data partition.
4. Select Repair or Change File System button.
5. And lastly select Resize File System button.
that solved the internal storage size, but the storage of sdcard shows 80MB when it should read 128GB.
I tryed the same method for sdcard but it cant be done on sdcard selection.
Is there any solution without formating sdcard?
if not please provide a solution with formating on twrp.
I have searched for a solution but no result...
Please help! i have no time to search right now!
Click to expand...
Click to collapse
Problem solved by replacing twrp with pitchblack ver.3 and repeating the procedure mentioned.